You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Controlling general BLDC motors by sinned6915 » Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
|
|
Flux linkage detection failed by Count1310 » Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
|
|
Cant get Rotor position to work by nancio » Mon, 2022-06-06 20:47 |
3 |
by frank Thu, 2022-06-09 09:05 |
|
|
Wiring a touchscreen to a vesc by posthy » Tue, 2022-06-14 10:22 |
3 |
by frank Thu, 2022-06-16 08:35 |
|
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic » Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
|
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 » Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
|
|
Sub zero temperature VESC412 issues by jetigm » Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
|
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 » Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
|
|
VESC 6+ CAN bus continued by kimpet » Fri, 2019-04-26 13:27 |
3 |
by Tinkerer Fri, 2021-04-02 06:31 |
|
|
Position accuracy by wall0069 » Sat, 2018-12-22 00:25 |
3 |
by sam.vanratt Thu, 2018-12-27 20:39 |
|
|
100k NTC by CTSchorsch » Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
|
|
Newbie - controller/motor not working by JLow75 » Tue, 2018-11-13 09:50 |
3 |
by bsissell Fri, 2021-11-26 07:17 |
|
|
Where to connect the Button for Reverse driver?, in ADC mode (Ebike throttle) by Astropower » Sun, 2019-05-19 22:10 |
3 |
by hackish Sun, 2019-09-08 05:31 |
|
|
bootloader destroied by notger » Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
|
|
VESC setup question for a motorised rope ascender. by Ben26 » Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
|
|
what is this part for by ynoo443 » Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
|
|
Lanyard kill switch by craig w » Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
|
|
How to prevent ground loop? by mansi712 » Fri, 2024-11-01 17:46 |
3 |
by Spaceman Thu, 2024-12-05 14:23 |
|
|
Undervoltage Fault by gazlinux » Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
|
|
How to reverse direction from VESC UART? by vinchi » Sat, 2022-01-08 23:03 |
3 |
by ergnmnh Thu, 2023-11-30 09:54 |
|
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly » Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
|
|
Advice needed: How to select KV value (or: how important is KV, in reality?) by c0d3z3r0 » Tue, 2024-09-03 09:23 |
3 |
by Groundspeed100 Tue, 2025-03-11 15:23 |
|
|
Can larger BLDC motors be controlled with VESC? by Heimfried » Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
|
|
can't reach the maximum speed by kingpon » Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
Log in to post new content in the forum.
