You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Need help with brushed fc 24 bolt motor control by searth » Sun, 2022-12-18 16:05 |
0 |
by searth Sun, 2022-12-18 16:05 |
|
|
Sensored mode studering by dtmpro621 » Thu, 2023-03-02 04:40 |
0 |
by dtmpro621 Thu, 2023-03-02 05:25 |
|
|
Recommended method for CAN Bus communication for 3 VESC by sivanhere » Sun, 2023-01-01 12:09 |
0 |
by sivanhere Sun, 2023-01-01 12:09 |
|
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
|
|
Any way to increase detection time? by VapeGod » Wed, 2023-01-25 05:58 |
0 |
by VapeGod Wed, 2023-01-25 05:58 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
Flipsky 4.20 plus with VX1 pro remote by Tropicalstorm » Tue, 2023-01-31 21:30 |
0 |
by Tropicalstorm Tue, 2023-01-31 21:30 |
|
|
Front hub motor on an X11 citycoco fat tire electric trike. by oangelo » Thu, 2022-12-08 22:57 |
0 |
by oangelo Thu, 2022-12-08 22:57 |
|
|
Why not using interrupt for Hall signal detection? by kuan » Sun, 2021-01-03 09:51 |
0 |
by kuan Sun, 2021-01-03 09:51 |
|
|
HFI when battery voltage is below HFI start voltage by rainebk@bigpond... » Thu, 2023-02-02 11:50 |
0 |
by rainebk@bigpond... Thu, 2023-02-02 11:50 |
|
|
Power cutoff without any warning by TylerWilson » Fri, 2022-12-09 06:37 |
0 |
by TylerWilson Fri, 2022-12-09 07:11 |
|
|
Using vesc between many motors by EliProtiva » Tue, 2021-02-16 05:32 |
0 |
by EliProtiva Tue, 2021-02-16 05:32 |
|
|
dual vesc question by badger1666 » Sun, 2018-10-28 12:59 |
0 |
by badger1666 Sun, 2018-10-28 12:59 |
|
|
PWM connection for a remote by dsuresh » Fri, 2021-02-19 19:17 |
0 |
by dsuresh Fri, 2021-02-19 19:17 |
|
|
Cruise function already implemented? by sam.vanratt » Wed, 2019-01-02 17:05 |
0 |
by sam.vanratt Wed, 2019-01-02 17:20 |
|
|
Set and measure RPM - Questions by Piep » Thu, 2018-11-08 16:10 |
0 |
by Piep Thu, 2018-11-08 16:10 |
|
|
Is it normal to have5th harmonic current ? by Alex Marques » Fri, 2023-02-10 16:01 |
0 |
by Alex Marques Fri, 2023-02-10 16:02 |
|
|
VESC on Chromebook? by Boa1277 » Sun, 2021-02-21 20:49 |
0 |
by Boa1277 Sun, 2021-02-21 20:49 |
|
|
Improper feedback from VESC Hardware with low speed ( SensorlessBEMF ) by Pranit Bhamare » Tue, 2023-02-14 07:19 |
0 |
by Pranit Bhamare Tue, 2023-02-14 07:19 |
|
|
Help needed please by Mark griffin » Tue, 2022-12-13 14:51 |
0 |
by Mark griffin Tue, 2022-12-13 14:51 |
|
|
How do I field weaken a bldc motor? I don’t see the setting by IPizzaI » Sat, 2024-05-11 18:50 |
0 |
by IPizzaI Sat, 2024-05-11 18:50 |
|
|
Measuring RPM using Hall sensors of BLDC motor by DEPL_PR24 » Fri, 2024-03-15 20:40 |
0 |
by DEPL_PR24 Fri, 2024-03-15 20:40 |
|
|
wheelchair with a joystick via Vesc by hopeingod » Fri, 2024-05-17 12:00 |
0 |
by hopeingod Fri, 2024-05-17 12:00 |
Log in to post new content in the forum.
