You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron on Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
General discussion | |
Autodetection values way off by thewho on Sat, 2019-05-25 20:34 |
28 |
by vadicus Mon, 2023-06-19 20:22 |
General discussion | |
Lehner TorQstar any experience by fabu80 on Wed, 2023-02-01 08:35 |
by fabu80 Wed, 2023-02-01 08:35 |
General discussion | ||
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
Controlling a Tank by JulianT on Thu, 2020-01-23 10:06 |
2 |
by frank Thu, 2023-03-23 18:28 |
General discussion | |
Dual VESC, Dual UART? by kneave on Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
General discussion | |
switching power supply by MagicKey on Tue, 2023-01-17 04:01 |
2 |
by vadicus Fri, 2023-06-23 22:59 |
General discussion | |
Push FW .bin File to Controller by vadicus on Wed, 2020-01-15 20:23 |
2 |
by vadicus Thu, 2020-01-16 17:35 |
General discussion | |
Vesc Suddenly stopped working by Erik on Wed, 2020-08-05 14:53 |
6 |
by Erik Tue, 2020-08-11 20:59 |
General discussion | |
Slowing down the speed when in low battery state by dsuresh on Tue, 2021-03-16 21:59 |
by dsuresh Tue, 2021-03-16 21:59 |
General discussion | ||
Flipsky 75100 controller not producing the same amount of power as esc controller at same current by Ashton on Mon, 2021-12-06 21:18 |
2 |
by Liam Li Sun, 2022-03-06 20:31 |
General discussion | |
Two Motors on same Shaft by Giga93 on Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
General discussion | |
VESC 4.12 with big-BLDC problem by sam.vanratt on Mon, 2018-12-10 15:59 |
6 |
by sam.vanratt Thu, 2019-01-03 17:44 |
General discussion | |
Flipsky 75100 and VEVOR MY1020D - Very jerky by DevelopedBug on Sat, 2022-07-16 19:46 |
6 |
by Trooth Fri, 2024-02-23 01:38 |
General discussion | |
Set McConf with no values --> bootloader erased? by Kakskiv on Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
General discussion | |
Bluetooth from vesc to pc issues by TyDaTyga on Wed, 2018-11-28 01:42 |
2 |
by badger1666 Fri, 2018-12-21 17:14 |
General discussion | |
Logging IMU Data over UART by stefan_novige on Mon, 2019-08-19 18:28 |
6 |
by pf26 Tue, 2019-08-27 13:44 |
General discussion | |
Custom VESC4 hardware - disable Regen? by ben5243 on Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
General discussion | |
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:45 |
by alexshen2012 Fri, 2022-07-01 05:45 |
General discussion | ||
VESC 75100 motor detection fine but then motor won't run just shudders and resistance by Jidobaba on Sun, 2024-04-21 03:17 |
by Jidobaba Sun, 2024-04-21 03:17 |
General discussion |