You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
How low is "low" inductance motors? by shaman on Sat, 2019-10-05 01:59 |
6 |
by MargaretHoffman Wed, 2023-02-22 23:07 |
General discussion | |
VESC Battery voltage discrepancy by Bender on Mon, 2021-03-15 14:23 |
by Bender Mon, 2021-03-15 14:23 |
General discussion | ||
Controller voor BLDC motor by Kapitein Nelson on Fri, 2022-04-29 17:26 |
1 |
by skyline1970 Thu, 2022-11-24 21:31 |
General discussion | |
Same MC Values, differnet Output on Dual Setup by E-Toxx on Mon, 2017-09-11 09:27 |
1 |
by Necromenz Mon, 2017-09-11 21:08 |
General discussion | |
VESC Input Using Raspberry Pi and Wiimote by Schizug on Wed, 2019-03-27 04:28 |
3 |
by Nelf Sat, 2020-08-08 01:13 |
General discussion | |
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 on Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
General discussion | |
PID gains by spacemango on Mon, 2020-06-08 21:16 |
1 |
by spacemango Tue, 2020-06-09 16:53 |
General discussion | |
Analogue throttle by craig w on Mon, 2022-01-03 07:56 |
2 |
by craig w Mon, 2022-01-03 09:25 |
General discussion | |
Solved: Cruise Control: Push to Activate; Cancel on BRK or Throttle Touched by vadicus on Wed, 2020-01-08 23:47 |
10 |
by vadicus Sat, 2024-02-17 01:37 |
General discussion | |
E-bike set up by Iangamblin on Fri, 2023-03-24 14:02 |
5 |
by Iangamblin Thu, 2023-06-29 17:35 |
General discussion | |
position control with gearbox by raess on Tue, 2018-09-25 23:48 |
18 |
by IanG Mon, 2020-03-30 06:44 |
General discussion | |
Do I need a motor with Hall sensor to use Vesc tool? by greew on Sun, 2020-05-31 06:48 |
by greew Sun, 2020-05-31 06:48 |
General discussion | ||
VESC LCD Display SPI by georgeli293 on Sun, 2024-01-14 20:06 |
1 |
by Sandro luis Thu, 2024-01-18 21:15 |
General discussion | |
VESC configuration with a high KV Motor by batdan on Sat, 2018-01-13 23:01 |
5 |
by Roger Wolff Sun, 2018-02-04 10:09 |
General discussion | |
Help calibrating a hub motor by Tin_Man_0 on Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
General discussion | |
FAULT_CODE_DRV Motor not spinning by Mightyorc on Sat, 2018-09-15 03:36 |
by Mightyorc Sat, 2018-09-15 03:36 |
General discussion | ||
No Option for Master or Slave on SetUp Input? by trickleung91 on Sun, 2019-06-30 09:06 |
1 |
by frank Sun, 2019-07-21 18:46 |
General discussion | |
Overcurrent fault by tomriddle425 on Fri, 2022-09-09 06:48 |
2 |
by Jean-Michel RAVON Tue, 2022-09-20 11:15 |
General discussion | |
Controlling general BLDC motors by sinned6915 on Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
General discussion | |
FOC and RC Helicopter (25KG) by Flyingtux on Tue, 2022-03-15 23:30 |
2 |
by Flyingtux Tue, 2022-03-29 17:12 |
General discussion |