You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Iron less Axialflux Motor by tobiokanobi » Sat, 2019-03-30 12:11 |
6 |
by kaanozgen Wed, 2020-02-26 11:42 |
|
|
How to wire MPU-9250 9DoF using SPI to vesc 6 mk4 by zmei116 » Fri, 2020-08-28 12:17 |
6 |
by TheFallen Mon, 2020-12-28 06:22 |
|
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 » Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
|
|
AS5047 with VESC75/300 by hpb66 » Mon, 2021-11-29 10:11 |
5 |
by canoeman Fri, 2022-01-28 20:17 |
|
|
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi » Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
|
|
Current measuring with DRV amplifiers by PXSS » Mon, 2018-02-12 03:14 |
5 |
by lizardmech Fri, 2018-03-02 00:43 |
|
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons » Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
|
|
VCC-GND short by caliber interconnect » Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
|
|
Dual VESC sync problem by Svenska Svenson » Wed, 2017-10-18 18:56 |
4 |
by Svenska Svenson Sat, 2017-10-28 13:47 |
|
|
VESC 75/300 liquid cooling by niekvanprooijen » Mon, 2019-09-09 19:15 |
4 |
by Mikko Valtonen Mon, 2020-08-17 07:21 |
|
|
Hall sensor not working by Stupidspencer » Sat, 2019-12-28 20:29 |
4 |
by BeliaEllet Wed, 2021-03-31 17:55 |
|
|
VESC 100/250 by electricfox » Mon, 2020-01-13 20:23 |
4 |
by vitormhenrique Thu, 2020-02-13 01:12 |
|
|
VESC on 48V 1500W HUB motor by jordanlow » Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
|
|
VESC6 Issues: Battery current inaccurate, positive ramp time, motor current max. by ESCam » Thu, 2019-03-21 22:50 |
4 |
by sp3swj Sat, 2022-03-19 15:07 |
|
|
3.3v short. is repair possible? by TZTZ » Sat, 2021-08-21 10:33 |
4 |
by tecnico.solarboat Mon, 2021-12-27 23:31 |
|
|
Are the FOC PID values for discrete or continuous time controllers? by ward » Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
|
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 » Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
|
|
Axial Flux motor control mode by ardillolambo » Wed, 2022-03-02 13:59 |
4 |
by ardillolambo Wed, 2022-03-02 18:25 |
|
|
2 VESC 100/200 single power on switch by tobiokanobi » Wed, 2022-08-31 16:06 |
4 |
by tobiokanobi Mon, 2022-09-05 11:44 |
|
|
VESC hardware schematics by cromoly » Tue, 2017-11-28 04:44 |
4 |
by ThierryGTLTS Tue, 2017-12-19 14:03 |
|
|
HARDWARE QUESTION: Maximum AC voltage VESC can tolerate? by danvel » Fri, 2018-04-27 15:31 |
4 |
by Roger Wolff Mon, 2018-05-14 22:13 |
|
|
VESC 75/300 with sin/cos encoder by sajjen » Tue, 2019-11-12 16:16 |
4 |
by marcos_ Sun, 2020-01-19 22:48 |
|
|
VESC 6.4 supplys Arduino over SIGNAL!! by MaxMaker1 » Thu, 2018-05-24 15:02 |
4 |
by frank Mon, 2018-06-04 23:24 |
|
|
Inductance (L) measurement by rahmaev_a_o » Tue, 2018-08-07 10:10 |
4 |
by benjamin Sat, 2019-02-23 10:11 |
|
|
VESC75/300 - Does your IMU work? by Gerhard » Mon, 2021-02-08 00:15 |
4 |
by Gerhard Thu, 2021-02-25 17:39 |
Log in to post new content in the forum.
