You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
|
How to select in VESC Tool the COM port of PC for USB connection to VESC6? by Heimfried » Mon, 2020-05-11 20:27 |
3 |
by Heimfried Wed, 2020-06-10 11:54 |
|
How to read the CAN message with CAN anlayzer by yuri12 » Thu, 2022-03-03 18:21 |
0 |
by yuri12 Thu, 2022-03-03 18:21 |
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
|
How to log events on a non bluetooth onewheel setup by carasta » Sat, 2023-05-13 22:01 |
0 |
by carasta Sat, 2023-05-13 22:01 |
|
How to keep motor at 0RPM by zapshe » Thu, 2022-09-08 13:51 |
3 |
by DaganWal Wed, 2023-07-19 04:38 |
|
How to increase startup torque? by Enak » Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
|
How to get vesc tool for linux on ubuntu? by vitormhenrique » Tue, 2019-10-22 16:00 |
7 |
by JackGunnarsson Mon, 2023-10-02 13:20 |
|
How to get Max Torque at start by player107 » Fri, 2023-04-07 09:55 |
4 |
by Trooth Fri, 2024-02-23 06:52 |
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
How to determine motor size in wizard, hub motors ? by Photolad61 » Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
how to communication with arduino on vesc via CAN by yuri12 » Tue, 2022-02-08 13:16 |
0 |
by yuri12 Tue, 2022-02-08 13:16 |
|
How to adjust ADC1 parameters to adjust the speed (not working) by player107 » Fri, 2023-04-14 13:46 |
0 |
by player107 Fri, 2023-04-14 13:46 |
|
How to access VESC error codes in the new VESC tool by berno3 » Tue, 2018-06-05 08:47 |
1 |
by Roger Wolff Wed, 2018-06-06 07:36 |
|
HOw do I run the vesc_tool_6.02 in ubuntu/linux by fwalker » Thu, 2024-05-02 22:57 |
0 |
by fwalker Thu, 2024-05-02 22:57 |
|
How do I disable brake? by moo10032 » Tue, 2021-02-23 08:09 |
0 |
by moo10032 Tue, 2021-02-23 08:10 |
|
How do I compile the VESC Tool? by ipbyrne » Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
|
How can we log all the real time data like motor current, battery current,etc to analyze them later? by vimi94 » Thu, 2019-05-02 09:57 |
27 |
by Stock88 Sun, 2024-11-03 04:02 |
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne » Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
2 |
by TheFallen Mon, 2020-08-17 12:14 |
|
Hoverboard motor Reverse direction by Silvio Semedo » Sat, 2021-01-16 17:43 |
1 |
by skyline1970 Sun, 2021-02-07 17:32 |
|
High Current Sampling Mode True 80% current by antonchromjak » Sun, 2017-09-24 21:14 |
2 |
by antonchromjak Wed, 2017-09-27 19:59 |
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:03 |
0 |
by stefann Wed, 2020-04-08 23:03 |
Log in to post new content in the forum.