You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC Tool returns bad ERPM value by karololo » Thu, 2019-10-03 10:12 |
1 |
by TechAUmNu Fri, 2019-10-04 15:05 |
|
|
How to determine motor size in wizard, hub motors ? by Photolad61 » Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
|
|
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik » Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
|
|
Disable bluetooth. by Roger Wolff » Sun, 2018-10-07 17:06 |
1 |
by arvidb Sun, 2018-10-07 17:27 |
|
|
Multiple VESC's in duty cycle mode by Rudolf10000 » Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
|
|
Description "Configuration for multiple VESCs via CAN-Bus" is missing in Documentation by Raphael » Wed, 2019-10-16 00:59 |
1 |
by frank Wed, 2019-11-06 13:00 |
|
|
vesc down load by mikeoutlaw24 » Fri, 2018-11-16 02:37 |
1 |
by frank Mon, 2018-12-10 17:32 |
|
|
Vesc Tool Mobile weird gps behavior by stefann » Tue, 2020-03-10 19:08 |
1 |
by benjamin Tue, 2020-03-17 09:46 |
|
|
GPDrive details? by shaman » Wed, 2020-03-11 19:05 |
1 |
by s0313045 Fri, 2021-02-05 08:34 |
|
|
Windows Bluetooth VESC 75/300 by Markula » Wed, 2019-11-06 17:33 |
1 |
by frank Fri, 2019-11-08 17:52 |
|
|
Unrecognized USB port vesc tool 1.25 by geotoine » Fri, 2019-11-08 15:35 |
1 |
by bb67 Fri, 2020-06-12 18:10 |
|
|
Another Motor Detection Thread by MaksK » Wed, 2019-01-02 21:05 |
1 |
by TechAUmNu Thu, 2019-01-03 17:23 |
|
|
Sensored FOC not working by Jarson » Thu, 2019-01-24 20:03 |
1 |
by Caustic_Zinc Fri, 2019-02-08 19:19 |
|
|
VESC Tool Android - Real-Time Data per controller or combined? by kamikatze13 » Sat, 2019-08-31 22:39 |
1 |
by Stupidspencer Sun, 2019-09-15 19:30 |
|
|
Parametre for Low RPM Limit by ilan248@gmail.com » Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
|
|
PPM mapping not working by Andytttt » Thu, 2020-01-09 05:58 |
1 |
by frank Mon, 2020-01-27 21:06 |
|
|
I need VESC Tool Version 1.13, please. by Astropower » Sun, 2019-09-08 18:22 |
1 |
by thewho Wed, 2019-09-18 08:29 |
|
|
Changing Output Voltage frequency by davbams » Wed, 2019-07-24 21:20 |
1 |
by district9prawn Thu, 2019-07-25 02:59 |
|
|
Please remove bootloader update section from FW Tab by sunbeam » Sun, 2019-09-15 01:12 |
1 |
by TechAUmNu Sat, 2020-06-27 09:33 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
|
|
PPM Mapping's VESC Tool not working by cornballs » Sun, 2019-09-22 09:17 |
1 |
by clistpdx Sat, 2020-10-24 02:40 |
|
|
inconsistent behavior after motor control using FOC by alexantosh » Wed, 2022-01-05 10:24 |
1 |
by frank Wed, 2022-01-05 11:21 |
|
|
Pictures from "Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller"? by timmertens » Thu, 2022-06-16 17:56 |
1 |
by frank Thu, 2022-06-16 19:47 |
|
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
Log in to post new content in the forum.
