You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Can not run again after run perfectly !! Pls help by Streetstar69 » Tue, 2021-11-23 03:03 |
1 |
by frank Tue, 2021-11-23 10:03 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
CAN packet ID for alive packets/heartbeat (still needs answer) by gcmoney » Tue, 2024-01-23 04:17 |
2 |
by gcmoney Thu, 2024-01-25 00:46 |
|
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly » Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
|
|
Can someone please post the steps to do position control from vesc tool? by dp » Wed, 2022-02-16 14:51 |
1 |
by frank Wed, 2022-02-16 17:24 |
|
|
Can someone verify this by jsbenson » Mon, 2023-06-26 09:22 |
0 |
by jsbenson Tue, 2023-06-27 07:50 |
|
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt » Tue, 2022-03-15 09:06 |
0 |
by v1n23nt Tue, 2022-03-15 09:10 |
|
|
Can VESC be in parallel connection with BMS while being charged? by dfelz » Tue, 2020-06-16 21:47 |
1 |
by TheFallen Wed, 2020-06-17 16:03 |
|
|
Can you switch censored to sensor less or HFI by diyRick » Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
|
|
Can you use both axes on a 2-axis nunchuck/joystick controller with VESC? by adamdorr » Tue, 2019-12-31 22:05 |
6 |
by sanketh1691 Sat, 2021-10-09 00:45 |
|
|
Can't access my forum post I made a few days ago by badgerthing » Wed, 2024-04-17 03:31 |
3 |
by electricfox Fri, 2024-05-10 22:12 |
|
|
can't communicate with arduino nrf by m.juan » Mon, 2018-07-02 16:57 |
0 |
by m.juan Mon, 2018-07-02 16:57 |
|
|
Can't connect to VESC's? Linux, need help? by ex-Gooserider » Wed, 2020-08-12 04:38 |
4 |
by ex-Gooserider Wed, 2020-08-19 01:39 |
|
|
Can't connect via Bluetooth anymore. by Stock88 » Wed, 2024-05-01 19:45 |
2 |
by amadden Wed, 2024-07-03 16:54 |
|
|
Can't download files from my account by STTrife » Sat, 2021-05-01 19:21 |
0 |
by STTrife Sat, 2021-05-01 19:21 |
|
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker » Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen » Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
|
|
can't reach the maximum speed by kingpon » Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
|
|
Can't receive status message via CAN bus by IanG » Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
|
|
Can't start a sensorless motor of a scooter by tobe81cwb » Mon, 2022-05-02 03:25 |
1 |
by skyline1970 Thu, 2022-11-24 21:36 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
Can't use the BLDC controller by hugog » Mon, 2025-09-08 12:00 |
6 |
by electricfox Fri, 2025-09-12 08:34 |
|
|
Canbus slave control in duty cycle mode not working correctly by Enak » Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
|
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
Log in to post new content in the forum.
