You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Driver explosion by fer-bo » Mon, 2021-07-05 11:48 |
4 |
by fer-bo Wed, 2021-07-07 14:50 |
|
Dead VESC. Power up when motor is spinning. by Bor Zabric » Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston » Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
|
foc observer/phase loosing track at phase current limit by Teslafly » Tue, 2018-07-24 18:46 |
4 |
by cir7 Thu, 2022-07-14 17:07 |
|
Has anyone tried Dc mode by TechAUmNu » Sun, 2018-05-13 14:28 |
4 |
by TechAUmNu Mon, 2018-05-14 15:16 |
|
FOC VESC for QS Motor 205 50H 3000w by karlisakis » Mon, 2021-06-07 21:29 |
4 |
by vadicus Mon, 2021-10-25 19:39 |
|
VESC - FAULT_CODE_DRV : motor no more spinning by piepolitb » Sat, 2018-05-19 12:27 |
4 |
by seif Wed, 2020-03-11 20:12 |
|
Sudden drop in speed after releasing throttle in FW mode by shokrabi » Sat, 2022-04-23 15:05 |
4 |
by DeuceDos Tue, 2023-05-30 09:54 |
|
Full Throttle direct after input deadband by toerde » Sat, 2022-04-30 18:54 |
4 |
by frank Mon, 2022-05-09 08:22 |
|
Problem with regenerative breaking by ligi » Sat, 2022-04-02 15:08 |
4 |
by ligi Sat, 2023-07-15 02:02 |
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog » Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
|
Flipsky 75/100 Mosfet short? by Michael Campbell » Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
|
FOC : Stop Motor without Active Brake by Flyingtux » Mon, 2022-03-14 12:35 |
4 |
by Flyingtux Tue, 2022-03-15 23:09 |
|
Improved low speed and full stop control with Hall by pf26 » Mon, 2020-06-08 19:33 |
4 |
by pf26 Tue, 2020-09-22 17:34 |
|
program motorstop for VTOL by Jan-Willem » Wed, 2020-04-29 18:55 |
4 |
by frank Thu, 2020-04-30 18:08 |
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar » Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
|
Positional Control, Hall Sensor by wdaehn » Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
|
Control singular VESC using CAN-BUS and Arduino by Cam » Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
|
Position control with Hall and A/B encoder by jo.rauchfuss » Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
|
Stall torque in sensorless mode by cromoly » Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho » Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
|
vesc6 help with hub motor by badger1666 » Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
|
Axiom's ESC with BLDC for Electric Motorcycle Conversion by ardillolambo » Tue, 2021-09-21 00:57 |
4 |
by alexrentier Thu, 2021-09-30 14:30 |
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt » Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
|
ADC control not linear or smooth by arranto12 » Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
Log in to post new content in the forum.