You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech » Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
|
|
enertionboard focbox : is vesc_tool safe to use? by fourchette » Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
|
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel » Fri, 2020-03-20 03:45 |
4 |
by thefallen Mon, 2021-03-01 16:47 |
|
|
Protect psu from regenerative braking by KarlGreger » Tue, 2020-01-28 03:45 |
4 |
by marc.s.cohn@gma... Tue, 2020-07-07 21:11 |
|
|
Why use sensorless if the motor has sensors? by j.konrad » Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
|
|
Using reverse with a spare channel by spork » Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
|
|
MOSFET failure and replacement, stormcore 60d by Airatic » Wed, 2022-01-19 11:36 |
4 |
by j.konrad Sat, 2022-01-22 01:17 |
|
|
Can't receive status message via CAN bus by IanG » Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
|
|
VESC Tool Instructions by brschaefer74 » Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
|
|
UART CAN forwarding by frankus » Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
|
|
VESC amplifier ? by Markula » Fri, 2020-11-13 14:52 |
4 |
by s0313045 Mon, 2020-11-16 23:50 |
|
|
BLDC Motor Power limitation by tecnico.solarboat » Tue, 2019-10-01 23:42 |
4 |
by tecnico.solarboat Thu, 2019-10-10 15:13 |
|
|
Setting up low KV brushless motor? by Trent » Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
|
|
Back EMF or motor voltage back to the supply by bdesvaux » Tue, 2022-09-27 09:22 |
4 |
by bdesvaux Wed, 2022-09-28 15:52 |
|
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar » Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
|
|
Sudden hard acceleration at around 30 km/h. Help by kristofferbenjaminw » Tue, 2022-10-04 17:31 |
4 |
by Chris Barth Tue, 2022-10-11 20:05 |
|
|
ADC throttle with braking by adobe75 » Thu, 2020-10-29 02:26 |
4 |
by gooki Mon, 2021-12-27 07:07 |
|
|
Positional Control, Hall Sensor by wdaehn » Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
|
|
Hall Sensors Not Detected by leymane » Fri, 2023-08-18 17:12 |
4 |
by Ben26 Mon, 2024-10-21 22:45 |
|
|
Rolling down-hill faster than my board's electric top speed by koralle » Tue, 2018-05-01 21:18 |
4 |
by koralle Sun, 2018-05-06 18:25 |
|
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston » Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
|
|
VESC 6 hi voltage problem by mike » Fri, 2018-05-04 11:34 |
4 |
by mike Tue, 2018-05-08 19:31 |
|
|
Too little torque. by Roger Wolff » Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
|
|
FOC VESC for QS Motor 205 50H 3000w by karlisakis » Mon, 2021-06-07 21:29 |
4 |
by vadicus Mon, 2021-10-25 19:39 |
|
|
How to read MotorRPM from UART to Arduino by azobe » Thu, 2018-03-08 14:42 |
4 |
by Muhammad Usman Fri, 2026-05-15 09:14 |
Log in to post new content in the forum.
