You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
can't communicate with arduino nrf by m.juan » Mon, 2018-07-02 16:57 |
0 |
by m.juan Mon, 2018-07-02 16:57 |
|
|
Can't connect to VESC's? Linux, need help? by ex-Gooserider » Wed, 2020-08-12 04:38 |
4 |
by ex-Gooserider Wed, 2020-08-19 01:39 |
|
|
Can't connect via Bluetooth anymore. by Stock88 » Wed, 2024-05-01 19:45 |
2 |
by amadden Wed, 2024-07-03 16:54 |
|
|
Can't download files from my account by STTrife » Sat, 2021-05-01 19:21 |
0 |
by STTrife Sat, 2021-05-01 19:21 |
|
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker » Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen » Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
|
|
can't reach the maximum speed by kingpon » Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
|
|
Can't receive status message via CAN bus by IanG » Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
|
|
Can't start a sensorless motor of a scooter by tobe81cwb » Mon, 2022-05-02 03:25 |
1 |
by skyline1970 Thu, 2022-11-24 21:36 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
Canbus slave control in duty cycle mode not working correctly by Enak » Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
|
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
|
|
Cannot downgrade from 5.03 to 5.02 by kallep » Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
|
|
Cannot reach max speed of BLDC motor by rousha42 » Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
|
|
Cannot use BLE in combination with Custom App anymore after upgrading by Gatze » Wed, 2021-10-06 12:27 |
1 |
by Gatze Thu, 2021-10-21 10:21 |
|
|
Canoe fun! Running rough/stepping at low speeds, 75200 Pro V2 ESC and 65121 Motor. by ajtalbot1 » Wed, 2024-07-31 05:49 |
8 |
by ajtalbot1 Sat, 2024-08-17 23:44 |
|
|
CanOpen by maxmertins » Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
|
|
Cant connect to Flipsky 75100 by Ed222 » Sun, 2022-03-20 00:31 |
3 |
by Ed222 Sun, 2022-03-20 19:01 |
|
|
Cant get Rotor position to work by nancio » Mon, 2022-06-06 20:47 |
3 |
by frank Thu, 2022-06-09 09:05 |
|
|
CAN_PACKET_STATUS_5 Current IN and Fault code by matrixgti » Tue, 2019-06-11 12:24 |
1 |
by STTS Fri, 2021-08-13 09:09 |
|
|
Can’t connect VESC tool to my ESC. Pls help by Comeback10 » Mon, 2024-09-16 23:08 |
0 |
by Comeback10 Mon, 2024-09-16 23:08 |
|
|
Change RPM of motor by Gas_Sn4ke » Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
|
|
Changing current sense output offset by bww129 » Fri, 2024-03-15 05:27 |
0 |
by bww129 Fri, 2024-03-15 05:27 |
|
|
Changing the Control Mode Using PPM by Nickicook4noswag » Mon, 2024-07-08 03:27 |
0 |
by Nickicook4noswag Mon, 2024-07-08 03:27 |
Log in to post new content in the forum.
