You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 » Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
|
Tuning strategy for a large motor? by MrSurly » Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman » Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
|
Two VESCs with servo-out firmware by _saeed_arabi_ » Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
|
Two vescs, one motor? by RoopeKuisma » Sun, 2020-05-10 22:11 |
17 |
by Elwin Thu, 2021-10-28 09:48 |
|
Two VESCs, two three-phase windings, one motor stator by kubark42 » Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
|
Type of motors supported by VESC 6 MKIV by Sami Sahli » Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
|
UART Accel/Gyro/Mag data by NATUITION » Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
|
UART Arduino Monitor by arranto12 » Thu, 2021-11-18 00:24 |
0 |
by arranto12 Thu, 2021-11-18 00:24 |
|
UART CAN forwarding by frankus » Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
|
UART communication by EthB » Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
|
UART GND to Battery (-), good idea ? by Pimousse » Sat, 2017-09-23 00:47 |
1 |
by Dillon Sat, 2018-03-17 05:56 |
|
uart position control by kragon » Sun, 2021-01-24 13:34 |
1 |
by kragon Thu, 2021-01-28 16:46 |
|
UAV motor BLDC detection fails by Torbjorn » Wed, 2022-10-12 13:54 |
1 |
by frank Wed, 2022-10-12 17:04 |
|
UAVCAN Versus Default VESC CAN Implementation by toma » Thu, 2019-06-13 09:17 |
6 |
by gjesusTec Tue, 2021-11-30 18:50 |
|
un-commanded reverse pulse by maxhurtz » Fri, 2022-09-02 16:01 |
5 |
by canoeman Thu, 2022-09-15 19:21 |
|
Unable to Detect Motor Sensors | 100/250 VESC | HPM5000B 72v 5kw GM Motor by Reichen Schaller » Sun, 2022-05-08 05:36 |
14 |
by Reichen Schaller Thu, 2022-05-19 22:27 |
|
Unable to turn on Smart Reverse by EBTEAM » Wed, 2022-11-02 08:35 |
1 |
by EBTEAM Wed, 2022-11-02 12:58 |
|
Under rated VESC for motor, problem? by Alistair Goodman » Wed, 2022-08-03 12:53 |
2 |
by Alistair Goodman Wed, 2022-08-03 15:27 |
|
Understanding Dual VESC (dual motors) setups by Cham » Mon, 2020-09-21 18:45 |
5 |
by ronmotor Fri, 2022-11-11 01:34 |
|
Understanding Kv and max RPM limit by ug79 » Fri, 2020-03-20 16:39 |
1 |
by Pimousse Sat, 2020-03-21 12:47 |
|
Understanding Results from "Experiments" (sweeps) by gazlinux » Thu, 2022-02-10 02:28 |
3 |
by frank Sun, 2022-02-13 11:41 |
|
understanding switching frequency and dutycycle by speed3r » Thu, 2019-08-08 13:36 |
3 |
by speed3r Thu, 2019-08-15 09:26 |
|
Undervoltage Fault by gazlinux » Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
Log in to post new content in the forum.