You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
VESC as voltage regulator in hybrid UAV by Bunda » Sun, 2022-07-10 08:01 |
1 |
by skyline1970 Thu, 2022-11-24 21:19 |
|
Fault code sensor 1 by krille » Sat, 2022-07-23 16:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:08 |
|
Hall effect sensor type for Flipsky 4.20 by braydinjones » Sun, 2022-07-24 01:06 |
1 |
by skyline1970 Thu, 2022-11-24 21:06 |
|
Open ESC for sensored 1/12 pan cars? by DocTrucker » Tue, 2022-08-02 08:33 |
1 |
by skyline1970 Thu, 2022-11-24 21:02 |
|
How to increase power ? by boursomaster » Sat, 2022-09-24 21:19 |
1 |
by skyline1970 Thu, 2022-11-24 20:19 |
|
Vesc edu 6 with 2800Kv brushless motor speed control by siklopentan » Sat, 2022-10-15 14:34 |
1 |
by skyline1970 Thu, 2022-11-24 20:12 |
|
Motor Driver Voltage Spike Problem by sersam » Sat, 2022-11-12 19:23 |
1 |
by skyline1970 Thu, 2022-11-24 20:00 |
|
Negative Current Spikes with Unloaded Hub Motor at Full Throttle (95% Duty) by vadicus » Wed, 2021-02-10 00:49 |
2 |
by Andreaa23 Tue, 2022-11-22 05:55 |
|
Flipsky 75100 e-bike ,controller gives low amperage at low rpm ,edit solved by mehmetoz1980 » Sun, 2022-11-20 17:55 |
2 |
by mehmetoz1980 Mon, 2022-11-21 13:29 |
|
what is HFI in the VESC? by dcameron » Sat, 2022-11-19 00:14 |
2 |
by dcameron Mon, 2022-11-21 02:07 |
|
Using VESC remote with non-VESC ESC by Ptkend » Tue, 2022-11-15 17:21 |
6 |
by Ptkend Sun, 2022-11-20 14:04 |
|
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi » Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
|
vesc, firmware, motor parameter calibration files? by dcameron » Fri, 2022-11-18 22:19 |
0 |
by dcameron Fri, 2022-11-18 22:19 |
|
status message by riku » Thu, 2022-11-17 05:31 |
1 |
by frank Thu, 2022-11-17 17:55 |
|
move source and header files to a folder by Jimny » Thu, 2022-11-17 05:45 |
0 |
by Jimny Thu, 2022-11-17 05:45 |
|
Can bus and BLDC vs FOC by Torbjorn » Fri, 2022-11-11 11:08 |
4 |
by Torbjorn Tue, 2022-11-15 14:37 |
|
Rion Tronic 250/ Focer3.1 using TC leads to explosion! by Drcfan » Mon, 2022-11-14 23:12 |
0 |
by Drcfan Tue, 2022-11-15 14:05 |
|
How to tune BLDC delay mode by Torbjorn » Tue, 2022-11-15 13:21 |
0 |
by Torbjorn Tue, 2022-11-15 13:21 |
|
forward, reverse, regen by ronmotor » Thu, 2022-11-10 22:37 |
2 |
by velolac Tue, 2022-11-15 12:06 |
|
Tuning strategy for a large motor? by MrSurly » Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
|
Am I shadowbanned? My posts never get any responses. Please respond if you see this. by MrSurly » Wed, 2022-11-02 02:02 |
2 |
by TooSlow2Care Mon, 2022-11-14 15:25 |
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 » Sat, 2022-11-12 03:12 |
0 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
|
Encoder Ratio for AS5047P by brian.s.stubbs@... » Fri, 2022-06-17 22:09 |
3 |
by XieMaster Fri, 2022-11-11 02:54 |
|
Understanding Dual VESC (dual motors) setups by Cham » Mon, 2020-09-21 18:45 |
5 |
by ronmotor Fri, 2022-11-11 01:34 |
|
Forum GUI by parasole » Fri, 2017-11-10 09:25 |
1 |
by VJPANDI Thu, 2022-11-10 15:07 |
Log in to post new content in the forum.