You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Choppiness in motor after half throttle by popeye243 » Tue, 2020-08-04 04:04 |
5 |
by vadicus Tue, 2020-09-15 23:53 |
|
|
acceleration speed and temp noise by badger1666 » Wed, 2018-04-04 20:18 |
5 |
by badger1666 Fri, 2018-04-06 20:13 |
|
|
Design custom VESC 6 Hardware by brightlightbeam » Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
|
|
hall sensor calibration. by Roger Wolff » Mon, 2018-04-16 11:17 |
5 |
by svs Mon, 2018-08-27 13:34 |
|
|
VESC 6 for AUV applications by bc » Thu, 2018-02-22 15:57 |
5 |
by arvidb Fri, 2018-02-23 19:20 |
|
|
Reverse rotation command during forward rotation by nisigundam » Wed, 2018-03-07 09:12 |
5 |
by Josh54 Thu, 2022-09-08 18:08 |
|
|
Rough transition to sensorless under load by vadicus » Sat, 2020-07-18 07:10 |
5 |
by vadicus Wed, 2020-08-05 20:10 |
|
|
Previous tool+5.2 by Phill Dixon » Sun, 2022-05-01 07:50 |
5 |
by firemaxx Thu, 2024-07-18 09:10 |
|
|
Current Control issue VESC4 by yosoufe » Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
|
|
What is a common motor efficiency? I'm at 72% by ever.summer » Tue, 2019-05-28 05:02 |
5 |
by Roger Wolff Sun, 2019-06-02 10:19 |
|
|
VESC on DIY CNC router by tbartoletta » Wed, 2019-02-20 03:00 |
5 |
by GunnarW Thu, 2019-02-21 16:44 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
Sudden kick (from motor current cut off?) by darowi » Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
|
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
|
VESC configuration with a high KV Motor by batdan » Sat, 2018-01-13 23:01 |
5 |
by Roger Wolff Sun, 2018-02-04 10:09 |
|
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
|
Motor shutting off due to FAULT_CODE_ABS_OVER_CURRENT by isso777 » Mon, 2022-01-24 13:56 |
5 |
by canoeman Thu, 2022-01-27 18:12 |
|
|
Vesc Max current 90A Vs ESC Max current 135A? by ScootScoot » Tue, 2021-12-14 13:00 |
5 |
by Markula Thu, 2021-12-16 20:42 |
|
|
step/dir by blueflower » Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
|
|
IMPSM Motor and Gearing by baein » Tue, 2022-01-25 11:19 |
5 |
by Rohan_Suresh_babu Sat, 2024-03-02 12:18 |
|
|
Logging additional Sensors with the VESC on the Phone App by palm369 » Sat, 2024-07-13 19:10 |
5 |
by palm369 Sun, 2024-11-10 13:13 |
|
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist » Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
|
|
On MOSFET choice and replacement by DarioP » Wed, 2020-09-30 14:11 |
5 |
by thefallen Fri, 2020-10-02 10:57 |
|
|
VESC FOC detecting running flawlessly, motor flipping direction erratically when running in speed and duty mode by DMKitsch » Fri, 2020-10-23 21:59 |
5 |
by milesf Wed, 2020-11-18 06:01 |
|
|
Pwm+dir input support by adilrepas » Tue, 2020-12-22 03:32 |
5 |
by skyline1970 Sat, 2021-02-06 19:32 |
Log in to post new content in the forum.
