You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Maker X - SV6 - FOC Detection Issues whatever the FW by okp » Mon, 2022-07-11 12:18 |
1 |
by Madaboutfoiling Sun, 2023-02-05 08:35 |
|
|
Requesting fault codes over UART by spork » Wed, 2020-06-24 09:02 |
1 |
by Pimousse Wed, 2020-07-01 12:50 |
|
|
SETUP FOR SINGLE BRUSHED MOTOR by mmatthews@aquav... » Fri, 2022-05-13 01:57 |
1 |
by skyline1970 Thu, 2022-11-24 21:39 |
|
|
Voltage variation and speed by bdesvaux » Mon, 2022-05-16 12:22 |
1 |
by frank Mon, 2022-05-16 20:52 |
|
|
Using the built-in gyro for RC cars by maxpla » Fri, 2020-06-26 10:49 |
1 |
by TechAUmNu Fri, 2020-06-26 16:09 |
|
|
[SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol by yes_wecangogreen » Wed, 2023-04-12 00:51 |
1 |
by yes_wecangogreen Sat, 2023-04-29 09:24 |
|
|
Connecting VESC to XAVIER by MrMonk3y » Wed, 2019-05-01 09:53 |
1 |
by MrMonk3y Wed, 2019-05-08 13:34 |
|
|
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline » Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
|
|
Power supply connection for multiple controllers by Caustic_Zinc » Wed, 2019-05-01 21:06 |
1 |
by giganticfizzy Sat, 2019-09-14 10:53 |
|
|
Input Setup Wizard Does Not Ask if Single or Multi VESC by kylemuramatsu » Wed, 2019-03-13 03:22 |
1 |
by benjamin Wed, 2019-03-13 09:38 |
|
|
Reverse direction by ISanberg » Sun, 2021-03-28 22:22 |
1 |
by skyline1970 Sat, 2021-09-18 12:01 |
|
|
Shutdown mode by Akeela23 » Sat, 2023-05-06 01:50 |
1 |
by Akeela23 Sat, 2023-05-06 01:56 |
|
|
VESC at very low speeds by LudoJ » Wed, 2019-05-15 16:09 |
1 |
by Roger Wolff Sun, 2019-06-02 10:25 |
|
|
DC-Link Capacitor Selection by rushi95 » Sat, 2019-05-18 12:15 |
1 |
by hexakopter Sat, 2019-05-18 12:39 |
|
|
BEFM (direct drive motor) higher than battery voltage. by BalorNG » Fri, 2021-04-02 18:04 |
1 |
by skyline1970 Sat, 2021-09-18 12:05 |
|
|
0 - 100% throttle in a sec by gadiati » Tue, 2019-04-02 21:45 |
1 |
by sam.vanratt Thu, 2019-04-04 18:40 |
|
|
Arduino UART communication HW4.10 FW3.56 by joseguerra » Wed, 2019-05-22 13:01 |
1 |
by Pimousse Thu, 2019-05-30 17:23 |
|
|
Flipsky 7550 and Ninebot Max G30 48V by shatty » Thu, 2021-03-11 07:02 |
1 |
by shatty Sat, 2021-03-13 04:55 |
|
|
Sync loss when switching from HALL to sensorless by blezalex » Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
|
|
VESC observer by knuthcomi » Sun, 2021-04-11 02:57 |
1 |
by knuthcomi Wed, 2021-04-14 00:07 |
|
|
Canbus slave control in duty cycle mode not working correctly by Enak » Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
|
|
Anyone building DRV8350 based VESC? by ZacharyDrew » Tue, 2019-04-16 02:14 |
1 |
by benjamin Tue, 2019-04-16 10:14 |
|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen » Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
|
|
Voltage vs Heating ? by marko » Thu, 2019-04-25 21:40 |
1 |
by moto_guy Fri, 2019-04-26 06:02 |
|
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung » Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
Log in to post new content in the forum.
