You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Power cutoff without any warning by TylerWilson » Fri, 2022-12-09 06:37 |
0 |
by TylerWilson Fri, 2022-12-09 07:11 |
|
|
Using vesc between many motors by EliProtiva » Tue, 2021-02-16 05:32 |
0 |
by EliProtiva Tue, 2021-02-16 05:32 |
|
|
PWM connection for a remote by dsuresh » Fri, 2021-02-19 19:17 |
0 |
by dsuresh Fri, 2021-02-19 19:17 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
|
|
Is it normal to have5th harmonic current ? by Alex Marques » Fri, 2023-02-10 16:01 |
0 |
by Alex Marques Fri, 2023-02-10 16:02 |
|
|
VESC on Chromebook? by Boa1277 » Sun, 2021-02-21 20:49 |
0 |
by Boa1277 Sun, 2021-02-21 20:49 |
|
|
Improper feedback from VESC Hardware with low speed ( SensorlessBEMF ) by Pranit Bhamare » Tue, 2023-02-14 07:19 |
0 |
by Pranit Bhamare Tue, 2023-02-14 07:19 |
|
|
Help needed please by Mark griffin » Tue, 2022-12-13 14:51 |
0 |
by Mark griffin Tue, 2022-12-13 14:51 |
|
|
anti theft possible? by hummina » Tue, 2021-02-23 07:44 |
0 |
by hummina Tue, 2021-02-23 07:44 |
|
|
Using Hall as encoder input by Offline » Tue, 2021-01-19 10:41 |
0 |
by Offline Mon, 2021-02-08 10:19 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
|
|
FOC settings are working in one VESC hardware and not in another VESC hardware with same hardware version ( VESC 6MKVI ) by Pranit Bhamare » Fri, 2023-02-17 07:17 |
0 |
by Pranit Bhamare Fri, 2023-02-17 07:17 |
|
|
display readings by FatsoBatso » Wed, 2021-02-24 18:01 |
0 |
by FatsoBatso Wed, 2021-02-24 18:01 |
|
|
Impact of motor resistance value vs temperature by Torbjorn » Fri, 2022-12-16 09:09 |
0 |
by Torbjorn Fri, 2022-12-16 09:09 |
|
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
|
|
Simultaneous control of two BLDC motors with VESCs via CAN bus without RC controller by sampatsr » Mon, 2023-02-27 20:21 |
0 |
by sampatsr Mon, 2023-02-27 20:21 |
|
|
Need help with brushed fc 24 bolt motor control by searth » Sun, 2022-12-18 16:05 |
0 |
by searth Sun, 2022-12-18 16:05 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
Sensored mode studering by dtmpro621 » Thu, 2023-03-02 04:40 |
0 |
by dtmpro621 Thu, 2023-03-02 05:25 |
|
|
Recommended method for CAN Bus communication for 3 VESC by sivanhere » Sun, 2023-01-01 12:09 |
0 |
by sivanhere Sun, 2023-01-01 12:09 |
|
|
Any way to increase detection time? by VapeGod » Wed, 2023-01-25 05:58 |
0 |
by VapeGod Wed, 2023-01-25 05:58 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
Flipsky 4.20 plus with VX1 pro remote by Tropicalstorm » Tue, 2023-01-31 21:30 |
0 |
by Tropicalstorm Tue, 2023-01-31 21:30 |
|
|
Front hub motor on an X11 citycoco fat tire electric trike. by oangelo » Thu, 2022-12-08 22:57 |
0 |
by oangelo Thu, 2022-12-08 22:57 |
|
|
Why not using interrupt for Hall signal detection? by kuan » Sun, 2021-01-03 09:51 |
0 |
by kuan Sun, 2021-01-03 09:51 |
Log in to post new content in the forum.
