You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Two VESCs, two three-phase windings, one motor stator by kubark42 » Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
|
|
Limit battery voltage during regen by f.damien12 » Mon, 2022-03-28 12:40 |
14 |
by drummerboy5408 Wed, 2023-06-28 05:33 |
|
|
ADC & UART. Bluetooth not working. by simon.rawlings » Sat, 2018-10-13 20:35 |
14 |
by Vdca Sun, 2024-01-14 23:21 |
|
|
VESC 6 DC motor Current limit? by ShortCircuit » Thu, 2019-02-07 21:56 |
14 |
by ShortCircuit Thu, 2019-03-14 19:34 |
|
|
Unable to Detect Motor Sensors | 100/250 VESC | HPM5000B 72v 5kw GM Motor by Reichen Schaller » Sun, 2022-05-08 05:36 |
14 |
by Reichen Schaller Thu, 2022-05-19 22:27 |
|
|
VESC for RC car application by andreas78 » Fri, 2018-02-09 13:56 |
14 |
by costaricakid Wed, 2024-01-24 23:40 |
|
|
VESC6 and CableCam by wdaehn » Sun, 2018-02-18 16:52 |
14 |
by willyfan Thu, 2018-03-01 09:42 |
|
|
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D » Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
|
|
Wand Cruise Control, and speed control only working on Master VESC by MaddiQ » Mon, 2019-09-16 20:46 |
15 |
by hans_maier Fri, 2019-10-11 00:22 |
|
|
Power switch on VESC 6 MK III by hans_maier » Mon, 2020-01-20 23:35 |
15 |
by frank Fri, 2022-12-23 12:41 |
|
|
3 speed switch by de-bodgery » Sat, 2021-08-21 02:22 |
17 |
by Oscar Lozano Gimenez Mon, 2023-05-22 14:07 |
|
|
Current Sensing in VESC by Toshi Sharma » Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
|
|
Two vescs, one motor? by RoopeKuisma » Sun, 2020-05-10 22:11 |
17 |
by Elwin Thu, 2021-10-28 09:48 |
|
|
Hall sensor filter on VESC flier board by raess » Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
|
|
simulate turboprop engine ... using VESC, how to.... by Eckehard » Wed, 2020-06-10 22:32 |
17 |
by Eckehard Thu, 2020-07-02 22:34 |
|
|
position control with gearbox by raess » Tue, 2018-09-25 23:48 |
18 |
by IanG Mon, 2020-03-30 06:44 |
|
|
FOC and very low speeds by verbeek » Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
|
|
VESC with really high KV by bengce » Sun, 2020-06-21 11:18 |
18 |
by bengce Thu, 2020-08-13 14:11 |
|
|
Using a VESC V4.12 for a machining lathe by Krampas » Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
|
|
DRV8302 sensibility by lurch » Sat, 2021-10-23 23:37 |
19 |
by lurch Sat, 2021-10-30 10:13 |
|
|
Is electronic brake always REGEN? by Tilman Baumann » Tue, 2018-04-10 11:16 |
19 |
by henxan Sun, 2019-11-17 18:30 |
|
|
Efficiency Control by devin » Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
|
|
UART communication by EthB » Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
|
|
Dual VESC with UART communication (Arduino) - how to communicate with slave over can ? by GargiMan » Thu, 2019-01-03 01:56 |
21 |
by Shubham07 Fri, 2023-03-31 10:49 |
|
|
Vesc 6 motor setup fault by Davo69URX » Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
Log in to post new content in the forum.
