You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
VESC 4.12 with big-BLDC problem by sam.vanratt » Mon, 2018-12-10 15:59 |
6 |
by sam.vanratt Thu, 2019-01-03 17:44 |
|
VESC 4.12 in a CityEL by twikis » Fri, 2018-01-12 15:54 |
6 |
by Roger Wolff Sat, 2018-01-20 16:14 |
|
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline » Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
|
vesc 100250 Off-the-shelf motor by cuaxr » Mon, 2021-10-25 11:59 |
0 |
by cuaxr Mon, 2021-10-25 11:59 |
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty » Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
|
VESC 100/250 Voltage spikes? by LondonNight » Mon, 2022-09-05 08:21 |
2 |
by LondonNight Fri, 2022-09-09 18:01 |
|
VESC 100/250 missing hall sensor plug by steve1428 » Sat, 2023-04-08 10:00 |
1 |
by iv.kravchenko Fri, 2023-05-19 22:26 |
|
VESC 100/250 IO Ports Protection by luke.flecknell » Wed, 2022-03-30 06:49 |
2 |
by luke.flecknell Wed, 2022-03-30 12:41 |
|
Vesc 100/250 for unsensored brushless motors by jmurba » Fri, 2022-08-05 12:05 |
3 |
by velolac Fri, 2022-08-12 22:14 |
|
VESC 100/250 For sale by jakemansbach » Sun, 2023-02-05 04:22 |
2 |
by EliProtiva Tue, 2023-02-28 00:12 |
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
VESC 100/250 by XBO » Tue, 2021-09-07 19:25 |
4 |
by frank Mon, 2021-09-20 14:01 |
|
VESC 100/250 by PBR-Automatyka » Tue, 2021-11-02 12:17 |
1 |
by PBR-Automatyka Tue, 2021-11-02 12:18 |
|
Vesc - UAVCAN - Pixhawk by dbau » Tue, 2022-02-01 07:43 |
1 |
by dbau Tue, 2022-02-01 07:57 |
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 » Wed, 2019-10-23 23:12 |
0 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
|
VESC - FAULT_CODE_DRV : motor no more spinning by piepolitb » Sat, 2018-05-19 12:27 |
4 |
by seif Wed, 2020-03-11 20:12 |
|
VESC - custom board by st0r » Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
|
VESC "underpowered" vs Kunteng Controller experience by andyw2005 » Thu, 2021-10-21 23:54 |
1 |
by Elwin Fri, 2021-10-22 11:39 |
|
Very Large hub motor detection (QSMOTOR 3000W hub) by shaman » Thu, 2020-02-20 01:26 |
5 |
by fart Wed, 2024-04-03 10:43 |
|
version of the vesc tool by aysubscriber@ic... » Tue, 2017-10-03 07:53 |
4 |
by aysubscriber@ic... Fri, 2017-10-13 03:47 |
|
Vedder forums or Vesc forums? by Eric » Wed, 2017-09-13 14:39 |
2 |
by frank Mon, 2017-09-18 10:12 |
|
VEC 4.20 50A current limitations by Jean-Michel RAVON » Thu, 2021-03-18 14:16 |
0 |
by Jean-Michel RAVON Thu, 2021-03-18 14:16 |
|
Valify V2 Robot Lawnmower by raess » Fri, 2018-04-27 09:07 |
7 |
by raess Wed, 2018-05-09 22:14 |
|
Using VESC to drive sensorless linear motor to simulate on/off solenoid by cmcraeslo » Wed, 2020-07-01 09:15 |
1 |
by pf26 Mon, 2020-07-06 11:10 |
|
Using VESC remote with non-VESC ESC by Ptkend » Tue, 2022-11-15 17:21 |
6 |
by Ptkend Sun, 2022-11-20 14:04 |
Log in to post new content in the forum.