You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant » Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
|
vesc canbus control PPM by JiaheXu » Thu, 2023-04-13 20:17 |
0 |
by JiaheXu Thu, 2023-04-13 20:17 |
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
VESC as Generator - Low Output at High Brake Current? by hoeken » Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 » Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
|
NEW and my motors sound like they work but hardly spin the wheels! by madurai85 » Sun, 2023-04-09 15:23 |
0 |
by madurai85 Sun, 2023-04-09 15:23 |
|
How to control PPM output with CANBUS command by JiaheXu » Thu, 2023-03-30 20:21 |
2 |
by JiaheXu Wed, 2023-04-05 16:52 |
|
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 » Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
|
VESC - custom board by st0r » Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
|
Dual VESC with UART communication (Arduino) - how to communicate with slave over can ? by GargiMan » Thu, 2019-01-03 01:56 |
21 |
by Shubham07 Fri, 2023-03-31 10:49 |
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen » Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
|
please delete! by return97 » Sat, 2022-07-23 17:31 |
4 |
by return97 Wed, 2023-03-29 17:28 |
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen » Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
|
VESC App - Android - "App not installed" error by KColborne » Mon, 2023-03-27 22:11 |
0 |
by KColborne Mon, 2023-03-27 22:11 |
|
3Shul 700A reporting negative current spikes by reobaird » Sat, 2023-03-25 03:22 |
0 |
by reobaird Mon, 2023-03-27 09:34 |
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
Configuration of underwater thruster by UnderwaterMotors » Fri, 2023-03-24 18:10 |
0 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
|
Controlling a Tank by JulianT » Thu, 2020-01-23 10:06 |
2 |
by frank Thu, 2023-03-23 18:28 |
|
Drive frequency and command rate question by jediengineer » Sun, 2023-03-19 19:07 |
0 |
by jediengineer Sun, 2023-03-19 19:08 |
|
FOC braking problem (FAULT_CODE_DRV) by iscle » Tue, 2018-05-29 15:16 |
29 |
by Zanooon97 Sat, 2023-03-18 20:11 |
|
Interfacing with the VESC using UART by dhruvna » Thu, 2023-03-16 17:42 |
0 |
by dhruvna Thu, 2023-03-16 17:42 |
|
Basic VESC troubleshooting (postmortem?) by N_COUNTER » Tue, 2023-03-14 10:58 |
0 |
by N_COUNTER Tue, 2023-03-14 11:01 |
|
Motor brake stuggling (Video) by Zanooon97 » Thu, 2023-03-09 18:57 |
2 |
by electricfox Mon, 2023-03-13 12:02 |
|
Is there a workaround to set regen voltage, not current? by Gsorter » Sat, 2023-03-11 17:59 |
2 |
by Gsorter Sat, 2023-03-11 23:48 |
Log in to post new content in the forum.