You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Full Throttle direct after input deadband by toerde » Sat, 2022-04-30 18:54 |
4 |
by frank Mon, 2022-05-09 08:22 |
|
|
Custom controlling software by neuromancer2701 » Tue, 2018-09-04 02:09 |
4 |
by LogixCraft Mon, 2022-01-03 13:33 |
|
|
Control singular VESC using CAN-BUS and Arduino by Cam » Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
|
|
Overvoltage Error during setup by arranto12 » Mon, 2021-11-08 23:22 |
4 |
by electricfox Tue, 2025-02-04 19:28 |
|
|
Axiom's ESC with BLDC for Electric Motorcycle Conversion by ardillolambo » Tue, 2021-09-21 00:57 |
4 |
by alexrentier Thu, 2021-09-30 14:30 |
|
|
ADC control not linear or smooth by arranto12 » Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
|
|
Position control with Hall and A/B encoder by jo.rauchfuss » Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
|
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho » Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
|
|
Stall torque in sensorless mode by cromoly » Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
|
|
Smooth control 3 phase sensored motor by spacewalker » Thu, 2020-07-23 07:25 |
4 |
by vadicus Fri, 2020-11-13 19:18 |
|
|
FW=ADC1, REV=ADC2 by ProgramThyself » Sat, 2020-08-01 23:30 |
4 |
by ProgramThyself Mon, 2020-08-03 03:56 |
|
|
Hub Motor Gives up while Coasting With No Faults by vadicus » Sun, 2020-08-09 01:36 |
4 |
by vadicus Tue, 2020-08-11 18:01 |
|
|
vesc6 help with hub motor by badger1666 » Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
|
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt » Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
|
|
Roll-to-start VESC by dsuresh » Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
|
|
e-bike hubmotor problem by Ratereducer » Fri, 2023-07-14 23:35 |
4 |
by Ratereducer Thu, 2023-09-07 23:31 |
|
|
VESC setup question for a motorised rope ascender. by Ben26 » Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
|
|
what is this part for by ynoo443 » Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
|
|
Lanyard kill switch by craig w » Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
|
|
How to prevent ground loop? by mansi712 » Fri, 2024-11-01 17:46 |
3 |
by Spaceman Thu, 2024-12-05 14:23 |
|
|
Undervoltage Fault by gazlinux » Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
|
|
How to reverse direction from VESC UART? by vinchi » Sat, 2022-01-08 23:03 |
3 |
by ergnmnh Thu, 2023-11-30 09:54 |
|
|
Advice needed: How to select KV value (or: how important is KV, in reality?) by c0d3z3r0 » Tue, 2024-09-03 09:23 |
3 |
by Groundspeed100 Tue, 2025-03-11 15:23 |
|
|
Can larger BLDC motors be controlled with VESC? by Heimfried » Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
Log in to post new content in the forum.
