You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Access denied when trying to connect by Robban » Sun, 2021-09-12 14:30 |
0 |
by Robban Sun, 2021-09-12 14:30 |
|
|
VESC controller configuration for 350W hub motor, 48V motor. by lukepankratz » Mon, 2024-04-15 19:54 |
0 |
by lukepankratz Mon, 2024-04-15 19:54 |
|
|
Vesc gps control by Erik » Thu, 2019-11-14 20:38 |
0 |
by Erik Thu, 2019-11-14 20:38 |
|
|
Device shutting down by gjos » Sun, 2024-04-21 22:23 |
0 |
by gjos Sun, 2024-04-21 22:23 |
|
|
motor stuttering and having a hard time with receiver ... help by okyuubix » Tue, 2021-09-14 23:43 |
0 |
by okyuubix Tue, 2021-09-14 23:49 |
|
|
RPi 5 and VESC over UART by XAQ » Wed, 2025-09-10 07:27 |
0 |
by XAQ Wed, 2025-09-10 19:33 |
|
|
VESC Software Understanding by shubhamt » Wed, 2018-08-22 15:40 |
0 |
by shubhamt Wed, 2018-08-22 15:40 |
|
|
How to confirm valid FOC operation? by _johnny_ » Wed, 2020-06-24 11:29 |
0 |
by _johnny_ Wed, 2020-06-24 11:29 |
|
|
mini fsesc4.20 help by bravo29 » Mon, 2026-03-16 17:14 |
0 |
by bravo29 Mon, 2026-03-16 17:14 |
|
|
VESC with Python on a RPi 5 by XAQ » Mon, 2025-09-15 01:06 |
0 |
by XAQ Mon, 2025-09-15 01:06 |
|
|
Fix to no running Fw by Draghici Ion » Wed, 2022-07-13 20:22 |
0 |
by Draghici Ion Thu, 2022-07-14 08:00 |
|
|
Bricked my VESC six what now? by atat » Sun, 2018-05-20 13:07 |
0 |
by atat Sun, 2018-05-20 14:28 |
|
|
Unstable current readings over VESC CAN (UART/USB are fine) by vukstijepovic » Mon, 2025-09-15 16:59 |
0 |
by vukstijepovic Mon, 2025-09-15 16:59 |
|
|
Field weakening in reverse? by Toymanfrank » Wed, 2026-04-15 04:40 |
0 |
by Toymanfrank Wed, 2026-04-15 04:40 |
|
|
customer app for pwm input by ccrbs » Tue, 2020-08-11 12:06 |
0 |
by ccrbs Tue, 2020-08-11 12:06 |
|
|
Runaway Motor with No BLE by Marctwo » Thu, 2020-07-02 20:47 |
0 |
by Marctwo Thu, 2020-07-02 20:47 |
|
|
Flipsky 65220 by mcfoilvesc » Sun, 2026-04-26 20:15 |
0 |
by mcfoilvesc Sun, 2026-04-26 20:15 |
|
|
Help - physical switch to change profiles on ADC15 by SwissCanuck » Sun, 2025-10-05 13:59 |
0 |
by SwissCanuck Sun, 2025-10-05 13:59 |
|
|
Cut-out at >40A by thewho » Thu, 2018-09-13 20:24 |
0 |
by thewho Thu, 2018-09-13 20:24 |
|
|
Issues using vesc for Gimbal Motor iPower GM5208-24 by marcnyffenegger » Fri, 2026-05-15 15:18 |
0 |
by marcnyffenegger Fri, 2026-05-15 15:18 |
|
|
Custom-made VESC PCB: High current sensor offset/Overcurrent fault during motor detection, possible hardware/firmware mismatch by Chinmay Mulgund » Mon, 2025-10-13 13:56 |
0 |
by Chinmay Mulgund Mon, 2025-10-13 14:02 |
|
|
Charging Li-ion battery using the VESC Harmony 32S BMS by sainihalj » Tue, 2025-10-14 14:42 |
0 |
by sainihalj Tue, 2025-10-14 14:42 |
|
|
[SOLVED]Motors "blocking totally" when throttling, after running VESC setup. by MaddiQ » Tue, 2018-06-12 21:01 |
0 |
by MaddiQ Tue, 2018-06-12 23:36 |
|
|
Dynamic Braking with resistor by jwhall » Sun, 2022-07-31 19:58 |
0 |
by jwhall Sun, 2022-07-31 23:51 |
|
|
Abs over current by Phill Dixon » Fri, 2022-06-03 17:26 |
0 |
by Phill Dixon Fri, 2022-06-03 17:26 |
Log in to post new content in the forum.
