You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 » Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
|
|
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi » Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
|
|
Current measuring with DRV amplifiers by PXSS » Mon, 2018-02-12 03:14 |
5 |
by lizardmech Fri, 2018-03-02 00:43 |
|
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 » Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
|
|
AS5047 with VESC75/300 by hpb66 » Mon, 2021-11-29 10:11 |
5 |
by canoeman Fri, 2022-01-28 20:17 |
|
|
VESC 100/250 won't go full duty cycle by TheBennis » Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
|
|
Iron less Axialflux Motor by tobiokanobi » Sat, 2019-03-30 12:11 |
6 |
by kaanozgen Wed, 2020-02-26 11:42 |
|
|
Adding capacitors with long power cables? by rich » Thu, 2017-09-07 20:40 |
6 |
by frank Mon, 2018-08-20 09:12 |
|
|
Total dead-time of the MOSFETs ???!! by ThierryGTLTS » Tue, 2017-09-12 17:08 |
6 |
by TechAUmNu Fri, 2018-01-26 10:37 |
|
|
Can't program bricked Vesc 6 over SWD by Rc 44 » Thu, 2019-06-20 02:16 |
6 |
by amit_bhar Thu, 2021-01-21 19:09 |
|
|
builtin ble on vesc 75_300 by alexefoil » Wed, 2019-07-03 02:35 |
6 |
by Glennisoty Thu, 2021-04-15 05:31 |
|
|
How to wire MPU-9250 9DoF using SPI to vesc 6 mk4 by zmei116 » Fri, 2020-08-28 12:17 |
6 |
by TheFallen Mon, 2020-12-28 06:22 |
|
|
VESC 100V 250A - don't reach 50000ERPM by tobiokanobi » Tue, 2022-04-12 19:29 |
6 |
by tobiokanobi Mon, 2022-05-02 19:22 |
|
|
VESC 75/300 UART connections to microcontroller by tecnico.solarboat » Sun, 2021-02-14 17:53 |
6 |
by TheFallen Fri, 2021-02-19 00:17 |
|
|
Disable throttle while braking This topic has been moved to "General discussion" (View topic) |
|||
|
100V vesc by paolowu64 » Tue, 2021-11-09 01:43 |
7 |
by vreppeto Mon, 2021-12-06 23:28 |
|
|
Bringup, pinouts, general manual... where to find? by kubark42 » Sun, 2021-03-07 03:32 |
7 |
by smith2e7 Tue, 2023-01-24 15:34 |
|
|
HW 4.12 Change low voltage cutoff by subodh.malgonde » Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
|
|
VESC 75/300 ABS_OVER_CURRENT by tecnico.solarboat » Mon, 2021-04-12 21:29 |
7 |
by Gerhard Thu, 2021-05-06 18:06 |
|
|
Power switch on VESCT6+ (MK3) by henry10210 » Thu, 2019-12-26 00:47 |
8 |
by henry10210 Tue, 2020-02-11 15:48 |
|
|
VESC 6 Schematic Question by mendez » Tue, 2019-02-12 07:11 |
8 |
by frank Thu, 2019-12-05 11:28 |
|
|
Vesc 75/300 burned by electricfox » Sat, 2020-02-15 22:35 |
8 |
by pf26 Fri, 2020-03-06 09:49 |
|
|
When 100250 is not enough by eptv » Sat, 2021-12-11 14:38 |
10 |
by eptv Wed, 2021-12-15 20:53 |
|
|
VESC Express - Logging by velolac » Mon, 2023-02-27 20:09 |
10 |
by electricfox Fri, 2024-03-22 22:02 |
|
|
VESC BMS Hardware Reference Design by DubP » Fri, 2021-09-03 21:00 |
10 |
by frank Wed, 2022-08-03 14:34 |
|
Log in to post new content in the forum.
