You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
HFI reference paper by jus133 » Mon, 2021-05-03 05:15 |
3 |
by benjamin Sun, 2021-11-07 12:09 |
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 » Sat, 2022-11-12 03:12 |
0 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
|
HFI when battery voltage is below HFI start voltage by rainebk@bigpond... » Thu, 2023-02-02 11:50 |
0 |
by rainebk@bigpond... Thu, 2023-02-02 11:50 |
|
Hi by elsie » Thu, 2018-01-25 02:49 |
0 |
by elsie Thu, 2018-01-25 16:23 |
|
High rpm issue kde3520xf by magnus.w » Fri, 2019-04-26 12:46 |
1 |
by magnus.w Sat, 2019-05-04 12:33 |
|
High speed braking failure by danspratt » Wed, 2020-07-22 23:58 |
11 |
by knuthcomi Sat, 2021-03-06 23:48 |
|
High voltage vesc 75/250 Field Weakening by reubarb.scons » Wed, 2022-03-02 08:45 |
2 |
by reubarb.scons Tue, 2022-03-15 07:14 |
|
highest battery current with 6.6? by devin » Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
|
HM-10 BLE adapter? by ziumus » Mon, 2019-04-22 00:42 |
0 |
by ziumus Mon, 2019-04-22 00:42 |
|
Holding torque in "Duty Cycle" mode by Petja » Mon, 2020-01-13 01:19 |
5 |
by pf26 Wed, 2020-03-04 08:58 |
|
Hoverboard Motor with VESC by mados73 » Wed, 2018-03-21 22:14 |
12 |
by Kirkness Mon, 2020-07-13 01:00 |
|
Hoverboard motors not spinning when manually controlled, work when doing hall test etc. by VK2EVA » Fri, 2020-12-25 22:01 |
2 |
by ATHIVEL Thu, 2021-02-18 15:45 |
|
How can I add watts data to solidgeek? by Fixitmoditbreakit » Sat, 2021-06-12 00:07 |
2 |
by vadicus Tue, 2021-06-15 17:50 |
|
How can I get current data from VESC to stm32f446re by hyedo » Sun, 2022-01-23 19:38 |
0 |
by hyedo Sun, 2022-01-23 19:38 |
|
how connect bluetooth module nRF52832 ? by netev » Mon, 2022-09-19 18:11 |
3 |
by frank Tue, 2022-09-20 12:38 |
|
How different of VESC 6 and VESC 4 by Ken_chen » Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
|
how do you arm your Vesc in arduino code? by the creator » Wed, 2019-03-13 01:11 |
0 |
by the creator Wed, 2019-03-13 01:33 |
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
how do you update the vesc tool by Phill Dixon » Fri, 2017-09-29 10:58 |
1 |
by ThierryGTLTS Fri, 2017-09-29 16:43 |
|
How do you wire one power-on push button to two VESC 6 MIIIs? by adamchicago » Mon, 2020-01-20 23:01 |
3 |
by tsharma Tue, 2021-09-14 10:14 |
|
How does controlling two different motors over CAN bus really work? by oangelo » Sat, 2023-04-15 20:05 |
0 |
by oangelo Sat, 2023-04-15 20:05 |
|
How does Current mode work by vescflyer » Thu, 2021-10-28 15:26 |
2 |
by vescflyer Fri, 2021-10-29 08:11 |
|
How does regenerative braking get enough voltage from my motor to charge my battery from ? by cnd » Wed, 2020-09-16 16:54 |
7 |
by flydr2 Mon, 2023-02-27 22:21 |
|
How does VESC measure the flux? by Jongwon » Thu, 2020-01-30 04:45 |
2 |
by pf26 Mon, 2020-02-10 16:18 |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung » Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
Log in to post new content in the forum.