You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC 75/300 vs VESC 100/250 by XBO » Tue, 2021-09-07 19:31 |
3 |
by flyingbrike Wed, 2021-09-08 13:42 |
|
|
Controlling VESC with arduino - by vulkan66 » Thu, 2019-07-11 11:51 |
3 |
by vulkan66 Thu, 2019-08-01 21:34 |
|
|
Problem with breaking in use in RC plane by fluffy » Tue, 2020-05-26 06:11 |
3 |
by fluffy Sat, 2020-05-30 03:54 |
|
|
Set McConf with no values --> bootloader erased? by Kakskiv » Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
|
|
Open source hardware? by Jens » Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
|
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 » Tue, 2020-04-21 17:40 |
3 |
by cjjohnson97 Fri, 2020-04-24 21:38 |
|
|
Magnetic 3 phase linear motor with VESC by Mr.ironic » Sun, 2020-06-07 18:17 |
3 |
by s0313045 Mon, 2020-06-08 11:41 |
|
|
swap PWM H and PWM L Pins on STM32F4 by Urs_Harry » Tue, 2022-03-15 23:04 |
3 |
by skyline1970 Thu, 2022-03-17 09:58 |
|
|
HELP!!! VESC 4.20 Dual with individual motor control by teit84 » Wed, 2020-06-10 20:03 |
3 |
by TheFallen Thu, 2020-06-18 11:48 |
|
|
Custom Built ESC based on VESC 6.6 by jordanlow » Sun, 2020-05-03 16:07 |
3 |
by regskd Tue, 2020-07-28 23:35 |
|
|
How to select COM port by Heimfried » Mon, 2020-05-04 22:23 |
3 |
by Heimfried Wed, 2020-06-10 11:55 |
|
|
Detection failed by Jetboard5 » Sat, 2025-03-22 01:28 |
3 |
by Jetboard5 Sat, 2025-03-22 20:29 |
|
|
Ideal Thermistor/Temperature Sensor? by josh » Sat, 2017-10-14 07:07 |
3 |
by josh Sun, 2017-10-22 06:52 |
|
|
How to avoid engine overheating? by oangelo » Thu, 2022-12-08 23:03 |
3 |
by vadicus Tue, 2022-12-13 22:39 |
|
|
What temerpature sensor and how do I use it? by evoheyax » Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
|
|
as5047d drift?,Vd voltage -10 by ziumus » Sat, 2021-02-20 20:38 |
3 |
by ziumus Tue, 2021-02-23 22:08 |
|
|
Getting started with bus control of the VESC by Invert » Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
|
|
Powering VESC and motor from powersupply by SIGURD » Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
|
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake » Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
|
|
Do I need phase voltage sense? by Flepple » Mon, 2021-01-25 15:31 |
3 |
by GPereira Thu, 2022-02-10 11:43 |
|
|
ADC control issue by dsuresh » Fri, 2021-03-05 18:21 |
3 |
by dsuresh Wed, 2021-03-10 19:45 |
|
|
Programming NRF51822 Module with ST-Link v2 by koralle » Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
|
|
Torque control setting by mambazhasa@uni.... » Thu, 2023-01-26 17:24 |
3 |
by Davidepolpi91 Tue, 2024-03-19 12:45 |
|
|
One motor runs fine, other one doesn't by Spamantha » Sun, 2021-09-12 17:00 |
3 |
by Spamantha Sun, 2021-09-26 12:03 |
|
|
Custom application and UART by Dennis Freiburg » Sat, 2020-01-11 13:19 |
3 |
by Dennis Freiburg Sun, 2020-01-12 19:37 |
Log in to post new content in the forum.
