You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
[SOLVED]Motors "blocking totally" when throttling, after running VESC setup. by MaddiQ » Tue, 2018-06-12 21:01 |
0 |
by MaddiQ Tue, 2018-06-12 23:36 |
|
|
[Solved]Command the throttle (ADC1) with a DAC by captaintoon » Sat, 2024-01-27 23:41 |
3 |
by captaintoon Sun, 2024-01-28 15:44 |
|
|
[SOLVED] PWM speed control at low RPM by comes04 » Sun, 2023-04-16 13:30 |
1 |
by comes04 Wed, 2023-05-03 20:44 |
|
|
[SOLVED] COMM_GET_VALUES on top of COMM_FORWARD_CAN not working by yes_wecangogreen » Sun, 2025-03-09 12:48 |
1 |
by yes_wecangogreen Wed, 2025-03-12 10:22 |
|
|
[SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol by yes_wecangogreen » Wed, 2023-04-12 00:51 |
1 |
by yes_wecangogreen Sat, 2023-04-29 09:24 |
|
|
[OT] Increase torque on DC brush motor by Riccio » Mon, 2022-03-28 19:32 |
2 |
by Riccio Tue, 2022-03-29 09:18 |
|
|
Your input needed: FESC 4.12 / Arduino / 4X 350W motors by matukash » Tue, 2020-07-21 16:36 |
6 |
by frank Fri, 2022-04-15 17:31 |
|
|
Xiaomi m365 mega upgrade by Tilman Baumann » Mon, 2018-02-12 12:25 |
47 |
by Grawp Wed, 2021-03-10 13:59 |
|
|
x12 issues by martysmotor » Fri, 2025-03-28 10:30 |
0 |
by martysmotor Fri, 2025-03-28 10:30 |
|
|
ws8212 and VESC firmware by dannlh » Fri, 2017-11-03 04:17 |
2 |
by dannlh Sat, 2017-11-04 18:47 |
|
|
Wrong software shows up. Answered my own question. by leecon » Fri, 2025-03-07 17:50 |
1 |
by leecon Tue, 2025-03-11 17:00 |
|
|
Wrong CAN termination resistor? by DarioP » Mon, 2022-06-13 21:27 |
3 |
by frank Thu, 2022-06-16 08:33 |
|
|
Wow wow by st0r » Sat, 2022-05-07 21:45 |
2 |
by Hansherrman Sun, 2022-10-30 01:40 |
|
|
Would like VESC 4.12 repair tips by spork » Wed, 2019-04-03 04:53 |
6 |
by spork Tue, 2019-04-23 11:01 |
|
|
Working on Open Source Remote Control for Differential Drive Robot using BLE by ilektron » Tue, 2021-11-30 03:02 |
1 |
by x78163 Wed, 2022-06-08 17:07 |
|
|
Wordle Bot tells you how good your guesses are. by Wordlebot » Mon, 2023-03-06 08:34 |
0 |
by Wordlebot Mon, 2023-03-06 08:34 |
|
|
Wolf king 11 gt 72v perimeters Help by jsherbz92 » Tue, 2025-04-01 05:52 |
0 |
by jsherbz92 Tue, 2025-04-01 05:52 |
|
|
Wiring two VESCs by neuromancer2701 » Mon, 2018-10-01 14:42 |
2 |
by arvidb Wed, 2018-10-03 23:41 |
|
|
Wiring TS5700N8501 by krassi_s » Sat, 2020-10-31 01:59 |
6 |
by TechAUmNu Tue, 2020-11-03 13:41 |
|
|
Wiring a touchscreen to a vesc by posthy » Tue, 2022-06-14 10:22 |
3 |
by frank Thu, 2022-06-16 08:35 |
|
|
Windows application by roeebloch » Mon, 2021-04-19 21:08 |
0 |
by roeebloch Mon, 2021-04-19 21:08 |
|
|
Windows 10 free tool wont open... by zip » Tue, 2024-07-02 09:48 |
1 |
by Josiah Eberharter Tue, 2024-07-30 06:41 |
|
|
Win10 BLE Error by jzy1115 » Tue, 2018-04-17 16:20 |
1 |
by spei Mon, 2019-03-04 13:55 |
|
|
will VESC synch with a 1020 inrunner? by Oded Mazor » Fri, 2022-02-18 16:58 |
1 |
by frank Fri, 2022-02-18 17:51 |
|
|
Will a Flipsky FSESC4.20 50A Controller Work with Unknown Motor? by Laurie Forbes » Thu, 2021-09-30 21:31 |
1 |
by andyw2005 Fri, 2021-10-22 00:09 |
Log in to post new content in the forum.
