You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Charge wires by Phill Dixon » Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
|
|
about reference hardware by qdxiatao » Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
|
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar » Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
|
|
RPM measurement. by Roger Wolff » Wed, 2017-11-29 16:48 |
2 |
by Roger Wolff Fri, 2017-12-01 06:25 |
|
|
Hub Motor Remote Control by bf01 » Tue, 2017-11-14 16:04 |
3 |
by frank Wed, 2017-12-06 23:41 |
|
|
Minimum speed by Davideo » Sat, 2017-10-21 17:40 |
7 |
by Davideo Thu, 2017-12-07 00:18 |
|
|
MOSFET driver delay compensation by e-biker » Sun, 2017-12-10 16:21 |
2 |
by e-biker Tue, 2017-12-12 09:41 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
|
Merry Christmas! by frank » Fri, 2017-12-22 14:31 |
4 |
by ThierryGTLTS Sun, 2017-12-24 14:34 |
|
|
Positional Control, Hall Sensor by wdaehn » Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
|
|
Motor rotation direction by e-biker » Fri, 2017-12-22 15:02 |
2 |
by e-biker Tue, 2018-01-02 13:15 |
|
|
FOC and extremely low speeds do not look sinusoidal by wdaehn » Wed, 2017-11-29 21:33 |
11 |
by Benjamin Mahony Wed, 2018-01-10 01:19 |
|
|
bootloader destroied by notger » Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
|
|
bldc motor detection with Focbox and 190kv motor by gicho » Mon, 2018-01-15 23:04 |
1 |
by linsus Wed, 2018-01-17 10:23 |
|
|
VESC 4.12 in a CityEL by twikis » Fri, 2018-01-12 15:54 |
6 |
by Roger Wolff Sat, 2018-01-20 16:14 |
|
|
Documentation by Cledus » Sat, 2017-12-30 22:23 |
1 |
by Oyta Tue, 2018-01-23 20:35 |
|
|
Hi by elsie » Thu, 2018-01-25 02:49 |
0 |
by elsie Thu, 2018-01-25 16:23 |
|
|
VESC configuration with a high KV Motor by batdan » Sat, 2018-01-13 23:01 |
5 |
by Roger Wolff Sun, 2018-02-04 10:09 |
|
|
Tachometer VS RPM by Davideo » Mon, 2018-02-05 03:17 |
2 |
by Davideo Tue, 2018-02-06 00:37 |
|
|
VESC 6.0 MCU Model? by josh » Thu, 2018-02-01 03:14 |
3 |
by josh Sat, 2018-02-10 19:17 |
|
|
Nunchuck app working for anyone? by Pedrodemio » Sat, 2018-02-10 04:11 |
1 |
by Pedrodemio Sun, 2018-02-11 01:00 |
|
|
ramping up RPM over uart (solved) by Davideo » Wed, 2018-02-14 13:13 |
2 |
by Davideo Thu, 2018-02-15 02:59 |
|
|
NRF Implementation by Christian » Thu, 2018-02-15 14:36 |
0 |
by Christian Thu, 2018-02-15 14:36 |
|
|
about the encoder and gimbal by qdxiatao » Fri, 2018-01-26 16:42 |
2 |
by benjamin Fri, 2018-02-23 13:44 |
Log in to post new content in the forum.
