You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Two vescs, one motor? by RoopeKuisma » Sun, 2020-05-10 22:11 |
17 |
by Elwin Thu, 2021-10-28 09:48 |
|
|
Current Sensing in VESC by Toshi Sharma » Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
|
|
Wand Cruise Control, and speed control only working on Master VESC by MaddiQ » Mon, 2019-09-16 20:46 |
15 |
by hans_maier Fri, 2019-10-11 00:22 |
|
|
Power switch on VESC 6 MK III by hans_maier » Mon, 2020-01-20 23:35 |
15 |
by frank Fri, 2022-12-23 12:41 |
|
|
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D » Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
|
|
ADC & UART. Bluetooth not working. by simon.rawlings » Sat, 2018-10-13 20:35 |
14 |
by Vdca Sun, 2024-01-14 23:21 |
|
|
Limit battery voltage during regen by f.damien12 » Mon, 2022-03-28 12:40 |
14 |
by drummerboy5408 Wed, 2023-06-28 05:33 |
|
|
VESC 6 DC motor Current limit? by ShortCircuit » Thu, 2019-02-07 21:56 |
14 |
by ShortCircuit Thu, 2019-03-14 19:34 |
|
|
VESC for RC car application by andreas78 » Fri, 2018-02-09 13:56 |
14 |
by costaricakid Wed, 2024-01-24 23:40 |
|
|
VESC6 and CableCam by wdaehn » Sun, 2018-02-18 16:52 |
14 |
by willyfan Thu, 2018-03-01 09:42 |
|
|
Unable to Detect Motor Sensors | 100/250 VESC | HPM5000B 72v 5kw GM Motor by Reichen Schaller » Sun, 2022-05-08 05:36 |
14 |
by Reichen Schaller Thu, 2022-05-19 22:27 |
|
|
VESC Stand-by and/or Shut-off. by ThierryGTLTS » Tue, 2017-10-31 10:58 |
13 |
by skyline1970 Sat, 2020-11-21 09:57 |
|
|
Two VESCs, two three-phase windings, one motor stator by kubark42 » Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
|
|
swagatron hoverboard motors with VESC by popeye243 » Tue, 2020-07-21 02:49 |
13 |
by popeye243 Mon, 2020-09-07 03:42 |
|
|
Factors of VESC motor detection and operation with 3rd Party Hardware by shaman » Wed, 2020-04-01 20:44 |
13 |
by vadicus Wed, 2020-05-13 00:23 |
|
|
2 vs 3 phase shunts by antonchromjak » Sun, 2018-04-15 13:25 |
13 |
by TechAUmNu Fri, 2019-02-15 18:57 |
|
|
Experience with QS120 IPM motor? by marvinrau » Mon, 2021-05-31 14:03 |
12 |
by pe Tue, 2021-11-16 18:20 |
|
|
ADC pin voltage not zero by zoppp » Fri, 2019-02-08 23:44 |
12 |
by zoppp Tue, 2019-03-12 01:17 |
|
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt » Thu, 2021-01-07 01:19 |
12 |
by vadicus Fri, 2021-01-22 18:14 |
|
|
FOC with encoder by Ledz » Tue, 2018-05-15 11:55 |
12 |
by ramesh Thu, 2023-12-21 07:22 |
|
|
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 » Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
|
|
"Could not read Firmware version" when connecting via Bluetooth by ligi » Tue, 2020-11-17 07:03 |
12 |
by BrianN Wed, 2024-01-31 17:48 |
|
|
Hoverboard Motor with VESC by mados73 » Wed, 2018-03-21 22:14 |
12 |
by Kirkness Mon, 2020-07-13 01:00 |
|
|
Its dead Jim...maybe (First 6 death?) by Jacob Lord » Fri, 2017-09-22 16:50 |
11 |
by frank Thu, 2017-10-05 09:23 |
|
|
Encoder connection by Herbie » Fri, 2019-05-31 15:12 |
11 |
by Dencio1976 Fri, 2022-10-21 13:46 |
Log in to post new content in the forum.
