You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman » Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
|
|
100k NTC by CTSchorsch » Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
|
|
Where to connect the Button for Reverse driver?, in ADC mode (Ebike throttle) by Astropower » Sun, 2019-05-19 22:10 |
3 |
by hackish Sun, 2019-09-08 05:31 |
|
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic » Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
|
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 » Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
|
|
VESC 6+ CAN bus continued by kimpet » Fri, 2019-04-26 13:27 |
3 |
by Tinkerer Fri, 2021-04-02 06:31 |
|
|
Undervoltage Fault by gazlinux » Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
|
|
How to reverse direction from VESC UART? by vinchi » Sat, 2022-01-08 23:03 |
3 |
by ergnmnh Thu, 2023-11-30 09:54 |
|
|
Advice needed: How to select KV value (or: how important is KV, in reality?) by c0d3z3r0 » Tue, 2024-09-03 09:23 |
3 |
by Groundspeed100 Tue, 2025-03-11 15:23 |
|
|
Can larger BLDC motors be controlled with VESC? by Heimfried » Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
|
|
Can’t connect VESC tool to my ESC. Pls help by Comeback10 » Mon, 2024-09-16 23:08 |
3 |
by Spaceman Thu, 2024-12-19 20:11 |
|
|
VESC setup question for a motorised rope ascender. by Ben26 » Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
|
|
what is this part for by ynoo443 » Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
|
|
Lanyard kill switch by craig w » Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
|
|
How to prevent ground loop? by mansi712 » Fri, 2024-11-01 17:46 |
3 |
by Spaceman Thu, 2024-12-05 14:23 |
|
|
Using a supercapacitor as an energy source by PV3e » Sat, 2020-10-10 17:25 |
3 |
by vadicus Tue, 2020-10-27 20:24 |
|
|
Fault:DRV8302 DUAL V4 by Lzx19961014 » Tue, 2018-09-04 11:48 |
3 |
by stone_1706 Sat, 2019-02-02 17:09 |
|
|
forum email notifications by jlcortex » Tue, 2018-06-05 15:30 |
3 |
by kubark42 Tue, 2021-10-05 21:15 |
|
|
SPINTEND UBOX 100v100a x2 or Flipsky 75100 100v100a x2 by DuckyTheDuck » Mon, 2022-09-26 12:07 |
3 |
by AngelKillR Wed, 2022-09-28 05:06 |
|
|
VESC for small drone (<1kg) by iKrosoft » Wed, 2018-10-03 16:40 |
3 |
by arvidb Thu, 2018-10-04 21:05 |
|
|
How different of VESC 6 and VESC 4 by Ken_chen » Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
|
|
Is there a way to use the 5 pin hall sensor with VESC? by Shivanshu Mahim » Fri, 2020-11-20 11:02 |
3 |
by Shivanshu Mahim Sat, 2020-11-21 19:34 |
|
|
lower power output than expected by mxpro32 » Tue, 2019-06-18 21:38 |
3 |
by frank Sun, 2019-07-21 18:39 |
|
|
Type of Hall sensor by Faheem » Thu, 2023-10-12 05:52 |
3 |
by Faheem Mon, 2023-10-23 10:02 |
|
|
[Solved]Command the throttle (ADC1) with a DAC by captaintoon » Sat, 2024-01-27 23:41 |
3 |
by captaintoon Sun, 2024-01-28 15:44 |
Log in to post new content in the forum.
