You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
PPM Signal not recognized by nopf » Mon, 2024-06-17 15:31 |
8 |
by nopf Tue, 2024-07-02 15:01 |
|
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma » Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
|
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs » Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
|
|
Communication with Vesc Tools by faheemift » Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
|
|
VSEC firmware update issue by dsuresh » Thu, 2021-02-11 17:25 |
8 |
by Macc Fri, 2021-06-11 13:10 |
|
|
Using dual VESC for Robot Control by Praveen » Sat, 2021-11-13 11:02 |
8 |
by Autocar Tue, 2021-12-07 21:30 |
|
|
Alien Power Systems Hall Sensors with VESC6 by lazerusrm » Tue, 2018-03-13 02:52 |
8 |
by faulknernolan Tue, 2022-07-05 11:36 |
|
|
Failure of FOC mode brake by jzy1115 » Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
|
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla » Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
|
|
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 » Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
|
|
5phase Vesc based on 75/300 by BartE » Thu, 2020-03-05 23:17 |
8 |
by vadicus Sun, 2020-03-08 05:51 |
|
|
VESC Battery Packs by frank » Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
|
|
Is this kogging and jitter in low rpms expected? by Snabelost » Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
|
|
VESC as Generator - Low Output at High Brake Current? by hoeken » Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
|
|
Newbie Help - ADC input by nickyg » Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
|
|
Difference between the current, duty cycle and PID speed control mode by tromes » Thu, 2020-06-11 07:51 |
8 |
by Onarb Kabr Wed, 2025-01-15 13:32 |
|
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze » Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
|
|
Upload bootloader to new MCU by Jessica » Fri, 2019-01-11 14:43 |
7 |
by Jessica Wed, 2019-01-16 09:07 |
|
|
E-scooter/bike throttle by Pelle van wijk » Sun, 2019-12-01 17:03 |
7 |
by hummina Wed, 2020-10-14 05:02 |
|
|
What is limiting the speed? by ProgramThyself » Wed, 2021-10-06 20:07 |
7 |
by ProgramThyself Sun, 2021-10-17 19:08 |
|
|
Current filters on VESC MKIII? by Elwin » Sat, 2021-11-06 11:16 |
7 |
by vadicus Thu, 2022-05-05 01:26 |
|
|
How does regenerative braking get enough voltage from my motor to charge my battery from ? by cnd » Wed, 2020-09-16 16:54 |
7 |
by flydr2 Mon, 2023-02-27 22:21 |
|
|
Fault code drv by Dominik139 » Wed, 2022-05-04 09:16 |
7 |
by frank Fri, 2022-05-06 08:02 |
|
|
PID Speed Control not working in ADC mode by a.smith » Mon, 2022-01-17 13:23 |
7 |
by lonelypanda Wed, 2023-11-15 08:40 |
Log in to post new content in the forum.
