You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Torque Ramp Rate whilst in FOC by J_W97 » Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
|
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak » Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
|
Torque control setting by mambazhasa@uni.... » Thu, 2023-01-26 17:24 |
3 |
by Davidepolpi91 Tue, 2024-03-19 12:45 |
|
Too little torque. by Roger Wolff » Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
|
Tmotor U8 and VESC6 FOC by protontim » Tue, 2017-10-10 22:44 |
26 |
by magnus.w Sun, 2019-04-28 18:45 |
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
Timeout Brake Current [Fail Save] by Cuprani » Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
|
Timeline and Source Openness by Geordi » Tue, 2017-09-05 13:35 |
2 |
by elux Fri, 2017-09-08 01:58 |
|
throttle programing by turbomullet » Sun, 2021-03-07 22:42 |
0 |
by turbomullet Sun, 2021-03-07 22:42 |
|
Throttle mapping issue by forcefed » Fri, 2018-03-30 15:37 |
2 |
by Burak Thu, 2023-12-07 13:21 |
|
Throttle curves by Phill Dixon » Wed, 2018-05-23 18:16 |
1 |
by Tilman Baumann Thu, 2018-05-24 11:33 |
|
Third Party Hardware Section - closed? by vadicus » Mon, 2023-07-03 07:15 |
1 |
by vadicus Wed, 2023-07-12 20:11 |
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
The motor with an enkoder of AS5048 rotates unevenly by densor » Thu, 2018-04-26 11:41 |
2 |
by densor Fri, 2018-04-27 08:27 |
|
the keyboard control doesn't work by dmarko16 » Sun, 2021-02-07 15:34 |
1 |
by skyline1970 Sun, 2021-02-07 17:13 |
|
temperature compensation make sense? by alexshen2012 » Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
|
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 » Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
|
Tachometer VS RPM by Davideo » Mon, 2018-02-05 03:17 |
2 |
by Davideo Tue, 2018-02-06 00:37 |
|
Synchronizing multiple motors before mechanically locking together by hockinsk » Sun, 2019-10-27 23:15 |
2 |
by Stupidspencer Sun, 2019-12-15 22:50 |
|
Sync loss when switching from HALL to sensorless by blezalex » Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
|
switching power supply by MagicKey » Tue, 2023-01-17 04:01 |
2 |
by vadicus Fri, 2023-06-23 22:59 |
|
Switching frequency factor 2 lower by Elwin » Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
|
Switching control scheme during opertion by Ben Murton » Tue, 2023-01-31 02:57 |
1 |
by Gos1 Mon, 2023-06-26 12:07 |
|
Switching between hall and observer by eptv » Thu, 2019-12-05 08:49 |
1 |
by frank Thu, 2019-12-05 10:54 |
|
Switch two Motor Profiles/Modes (UART) by anli » Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
Log in to post new content in the forum.