You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 » Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
|
|
Hub motor stutters at low RPM by winpark » Wed, 2020-09-02 00:53 |
3 |
by vadicus Tue, 2020-09-15 18:14 |
|
|
Sub zero temperature VESC412 issues by jetigm » Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
|
|
Position accuracy by wall0069 » Sat, 2018-12-22 00:25 |
3 |
by sam.vanratt Thu, 2018-12-27 20:39 |
|
|
Question on throttle response by petermarcotte1 » Wed, 2020-07-29 11:28 |
3 |
by petermarcotte1 Sat, 2020-08-01 14:17 |
|
|
Newbie - controller/motor not working by JLow75 » Tue, 2018-11-13 09:50 |
3 |
by bsissell Fri, 2021-11-26 07:17 |
|
|
Upload bootloader to stm32 f405? by jneumann » Sat, 2020-08-08 07:11 |
3 |
by TechAUmNu Sat, 2020-08-08 18:29 |
|
|
tuning low kv high pole sensorless outrunner by cdlapoin » Tue, 2025-05-20 22:14 |
3 |
by flagoworld Wed, 2025-12-10 19:29 |
|
|
swap PWM H and PWM L Pins on STM32F4 by Urs_Harry » Tue, 2022-03-15 23:04 |
3 |
by skyline1970 Thu, 2022-03-17 09:58 |
|
|
Detection failed by Jetboard5 » Sat, 2025-03-22 01:28 |
3 |
by Jetboard5 Sat, 2025-03-22 20:29 |
|
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
|
VESC 6+ CAN bus continued by kimpet » Fri, 2019-04-26 13:27 |
3 |
by Tinkerer Fri, 2021-04-02 06:31 |
|
|
Torque control setting by mambazhasa@uni.... » Thu, 2023-01-26 17:24 |
3 |
by Davidepolpi91 Tue, 2024-03-19 12:45 |
|
|
Programming NRF51822 Module with ST-Link v2 by koralle » Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
|
|
100k NTC by CTSchorsch » Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
|
|
How to avoid engine overheating? by oangelo » Thu, 2022-12-08 23:03 |
3 |
by vadicus Tue, 2022-12-13 22:39 |
|
|
as5047d drift?,Vd voltage -10 by ziumus » Sat, 2021-02-20 20:38 |
3 |
by ziumus Tue, 2021-02-23 22:08 |
|
|
Powering VESC and motor from powersupply by SIGURD » Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
|
|
What temerpature sensor and how do I use it? by evoheyax » Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
|
|
Where to connect the Button for Reverse driver?, in ADC mode (Ebike throttle) by Astropower » Sun, 2019-05-19 22:10 |
3 |
by hackish Sun, 2019-09-08 05:31 |
|
|
Getting started with bus control of the VESC by Invert » Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
|
|
Do I need phase voltage sense? by Flepple » Mon, 2021-01-25 15:31 |
3 |
by GPereira Thu, 2022-02-10 11:43 |
|
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake » Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
|
|
ADC control issue by dsuresh » Fri, 2021-03-05 18:21 |
3 |
by dsuresh Wed, 2021-03-10 19:45 |
|
|
HELP! Underpowered motor! by natebakesacake123 » Thu, 2024-02-08 04:22 |
3 |
by natebakesacake123 Thu, 2024-02-08 21:22 |
Log in to post new content in the forum.
