You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Up dating firmware by rossco1959 » Mon, 2020-01-06 03:44 |
3 |
by rossco1959 Wed, 2020-01-08 02:06 |
|
|
UART Accel/Gyro/Mag data by NATUITION » Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
Accessing the status LEDs by hrucker009 » Sun, 2020-01-05 20:09 |
1 |
by frank Tue, 2020-01-07 09:08 |
|
|
Help calibrating a hub motor by Tin_Man_0 » Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
|
|
Protecting PSU with resistive load when braking by henxan » Sat, 2019-11-16 21:08 |
8 |
by Stupidspencer Mon, 2019-12-30 18:02 |
|
|
VESC6+ compatible 540 1/10 BLDC motor recommendation by henry10210 » Tue, 2019-12-17 08:15 |
3 |
by benjamin Sun, 2019-12-22 09:56 |
|
|
VESC recommendation for sailboat conversion by Henque19 » Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
|
|
Two VESCs with servo-out firmware by _saeed_arabi_ » Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
|
|
Position control with Hall and A/B encoder by jo.rauchfuss » Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
|
|
Synchronizing multiple motors before mechanically locking together by hockinsk » Sun, 2019-10-27 23:15 |
2 |
by Stupidspencer Sun, 2019-12-15 22:50 |
|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
|
I How do I find developers that work with the VESC. by AK6302019 » Sun, 2019-08-04 01:42 |
3 |
by jchillerup Wed, 2019-12-11 09:20 |
|
|
Calculator by kstuck » Tue, 2019-12-10 18:30 |
0 |
by kstuck Tue, 2019-12-10 18:30 |
|
|
missing Analog Throttle failsafe by bosko » Thu, 2019-12-05 16:47 |
5 |
by bosko Fri, 2019-12-06 13:25 |
|
|
Problem with Bluetooth connection (HM-10) by squdowx » Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
|
|
Sensorless mode with brushless motor with no sensor by focy » Wed, 2019-12-04 09:05 |
1 |
by frank Thu, 2019-12-05 11:07 |
|
|
Switching between hall and observer by eptv » Thu, 2019-12-05 08:49 |
1 |
by frank Thu, 2019-12-05 10:54 |
|
|
Setting up low KV brushless motor? by Trent » Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
|
|
Advice please - VESC6 controller for a specific model aircraft application by aabill » Wed, 2019-11-27 11:31 |
5 |
by frank Sun, 2019-12-01 17:28 |
|
|
Modification to higher voltage by jklmuk » Sun, 2019-11-24 12:33 |
3 |
by jklmuk Fri, 2019-11-29 18:00 |
|
|
Is this (low-inertia) application likely to be problematic by aabill » Sat, 2019-11-23 20:54 |
2 |
by aabill Thu, 2019-11-28 14:36 |
|
|
anti spark circuit by renaudbarbier » Mon, 2019-11-11 12:21 |
1 |
by frank Thu, 2019-11-28 10:01 |
|
|
Sensorless BLDC motor by Pelle van wijk » Sun, 2019-11-24 15:18 |
1 |
by frank Thu, 2019-11-28 09:56 |
|
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
Log in to post new content in the forum.
