You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Small motor with vesc? by spacemango » Mon, 2020-06-08 21:14 |
5 |
by spacemango Tue, 2020-06-16 15:30 |
|
|
Small inrunner HFI set-up issue by anthony_ » Thu, 2022-08-11 13:43 |
2 |
by anthony_ Mon, 2022-08-15 13:45 |
|
|
Slowing down the speed when in low battery state by dsuresh » Tue, 2021-03-16 21:59 |
0 |
by dsuresh Tue, 2021-03-16 21:59 |
|
|
Slow down deacceleration?? by yulaw2k » Tue, 2020-03-17 07:16 |
1 |
by vadicus Wed, 2020-03-18 16:56 |
|
|
Slow acceleration / no initial torque? by tobe81cwb » Fri, 2022-05-20 00:04 |
1 |
by Gatze Sat, 2022-05-21 17:16 |
|
|
Slow ABS current limit. by Faheem » Tue, 2023-10-24 07:49 |
0 |
by Faheem Tue, 2023-10-24 07:49 |
|
|
Slot car ESC? by adrianblakey » Thu, 2022-10-13 11:52 |
1 |
by frank Thu, 2022-10-13 14:49 |
|
|
Slight stutter when sensor mode turns off by rg12 » Wed, 2022-01-05 01:18 |
4 |
by frank Mon, 2022-01-10 08:21 |
|
|
Sleep timer never gets activated by robertkovax » Thu, 2023-09-14 21:11 |
1 |
by robertkovax Sat, 2023-09-16 21:53 |
|
|
SkyPuff paragliding, wakeboard winch new proto by eptv » Tue, 2021-02-16 09:56 |
1 |
by Engan Sun, 2021-03-14 13:06 |
|
|
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette » Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
|
|
SINE/COS encoder makes motor not work by DHOUT » Mon, 2023-01-30 05:23 |
0 |
by DHOUT Wed, 2023-02-01 03:00 |
|
|
Simultaneous control of two BLDC motors with VESCs via CAN bus without RC controller by sampatsr » Mon, 2023-02-27 20:21 |
0 |
by sampatsr Mon, 2023-02-27 20:21 |
|
|
Simulating controller accurately by TechAUmNu » Fri, 2019-08-16 15:35 |
0 |
by TechAUmNu Fri, 2019-08-16 15:35 |
|
|
simulate turboprop engine ... using VESC, how to.... by Eckehard » Wed, 2020-06-10 22:32 |
17 |
by Eckehard Thu, 2020-07-02 22:34 |
|
|
Shutdown mode by Akeela23 » Sat, 2023-05-06 01:50 |
1 |
by Akeela23 Sat, 2023-05-06 01:56 |
|
|
Should I drive a HDD motor with VESC or some other chip? by arildj78 » Tue, 2018-05-22 09:09 |
1 |
by arildj78 Wed, 2018-05-23 12:26 |
|
|
SETUP FOR SINGLE BRUSHED MOTOR by mmatthews@aquav... » Fri, 2022-05-13 01:57 |
1 |
by skyline1970 Thu, 2022-11-24 21:39 |
|
|
Settings by aquamarin » Sat, 2023-07-01 16:11 |
0 |
by aquamarin Sat, 2023-07-01 16:11 |
|
|
Setting up low KV brushless motor? by Trent » Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
|
|
Setting up flipsky by JanneHooo » Sat, 2023-10-14 13:07 |
2 |
by JanneHooo Sun, 2023-10-15 13:18 |
|
|
Setting the motor parameters by Lenar » Sat, 2024-05-04 10:18 |
0 |
by Lenar Sat, 2024-05-04 10:18 |
|
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot » Thu, 2022-12-15 22:03 |
0 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON » Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
|
|
Set RPM - reverse direction over CAN-Bus by 65273 » Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
Log in to post new content in the forum.
