You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
SPINTEND UBOX 100v100a x2 or Flipsky 75100 100v100a x2 by DuckyTheDuck » Mon, 2022-09-26 12:07 |
4 |
by primarc1982 Sat, 2026-05-09 07:16 |
|
|
Position control with Hall and A/B encoder by jo.rauchfuss » Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
|
|
FSESC 4.20 Tuning for RC ESC? by Abcc123 » Thu, 2022-09-01 04:41 |
4 |
by Abcc123 Wed, 2022-09-07 00:23 |
|
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho » Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
|
|
Hub Motor Gives up while Coasting With No Faults by vadicus » Sun, 2020-08-09 01:36 |
4 |
by vadicus Tue, 2020-08-11 18:01 |
|
|
Motor temperature increase by e-biker » Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
|
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
|
Difference between Brake Current, Full Brake etc by wdaehn » Wed, 2018-02-21 15:32 |
4 |
by rodread Sat, 2018-03-03 10:45 |
|
|
Firmware update thru UART? by cromoly » Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
|
|
Removing low speed openloop FOC parking brake mode from FW by rodread » Thu, 2018-03-08 15:01 |
4 |
by arvidb Wed, 2018-06-06 19:02 |
|
|
Can motor parameters be detected with shaft load? by powerlabor001 » Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
|
|
Smooth control 3 phase sensored motor by spacewalker » Thu, 2020-07-23 07:25 |
4 |
by vadicus Fri, 2020-11-13 19:18 |
|
|
FW=ADC1, REV=ADC2 by ProgramThyself » Sat, 2020-08-01 23:30 |
4 |
by ProgramThyself Mon, 2020-08-03 03:56 |
|
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy » Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
|
|
Set RPM - reverse direction over CAN-Bus by 65273 » Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
|
|
Updated VESC 6 schematic request by ma-j-sterelektron » Mon, 2019-03-25 08:43 |
4 |
by jejaj25773 Fri, 2024-07-26 02:29 |
|
|
Hybrid mode in FOC - possible? by Oded Mazor » Tue, 2022-04-12 07:42 |
4 |
by Oded Mazor Wed, 2022-04-13 11:28 |
|
|
half speed on FOC vs BLDC by ever.summer » Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
|
|
Roll-to-start VESC by dsuresh » Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
|
|
Getting Started / Prototyping Help by harrym » Wed, 2020-04-01 17:56 |
4 |
by javmarina Sat, 2020-05-09 17:35 |
|
|
CanOpen by maxmertins » Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
|
|
Is the Vesc 5 mkIII capable of 13s li-Ion (fully charged 54,6V) by Pelle » Sun, 2020-04-12 12:09 |
4 |
by danilolattaro Thu, 2021-04-22 14:50 |
|
|
Handbrake in PPM mode by bdesvaux » Wed, 2024-03-20 17:49 |
4 |
by its4ankit Sun, 2024-05-12 17:41 |
|
|
Starting rotation by changing duty cicle- current increases shortly (ms) and dcreases immediately to 0A by simon_snow » Wed, 2021-10-06 22:15 |
4 |
by simon_snow Fri, 2021-10-08 12:49 |
|
|
FOC observer error. by Roger Wolff » Thu, 2018-06-07 13:43 |
4 |
by district9prawn Wed, 2018-12-12 23:44 |
Log in to post new content in the forum.
