You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Vesc can't connect to vesc tool by Roansky1 » Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
|
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 » Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
|
|
VESC Tool speed control overshoot by PKmita » Tue, 2022-04-26 16:05 |
0 |
by PKmita Tue, 2022-04-26 16:12 |
|
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi » Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
|
|
Lisp scripting questions/suggestions/remarks by Gatze » Sun, 2022-04-24 12:13 |
0 |
by Gatze Sun, 2022-04-24 13:00 |
|
|
VESC Tool app min hardware requirements by flix » Sat, 2022-04-16 22:13 |
0 |
by flix Sat, 2022-04-16 22:13 |
|
|
Smart Reverse Minimum Erpm by ZenRides » Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
|
|
Feature request: Raw hall data. by Roger Wolff » Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
|
|
foc openloop not starting motor on higher erpm by Alan oldguy » Thu, 2018-09-06 08:43 |
8 |
by technicc Mon, 2022-03-28 09:23 |
|
|
5000 rpm BLDC, 1600 rpm FOC by scubersteve » Mon, 2022-03-21 03:10 |
1 |
by skyline1970 Fri, 2022-03-25 18:45 |
|
|
Failure to download VESC Tool by CallumMac » Tue, 2022-01-25 02:38 |
26 |
by Ian Watts Wed, 2022-03-16 12:25 |
|
|
VESC tool windows 10 connection via bluetooth by th0masrtg » Thu, 2020-09-24 14:20 |
11 |
by sp3swj Tue, 2022-03-15 03:08 |
|
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
|
How to read the CAN message with CAN anlayzer by yuri12 » Thu, 2022-03-03 18:21 |
0 |
by yuri12 Thu, 2022-03-03 18:21 |
|
|
RT Data, v3.01, Amazon Fire Tablet (sideloaded) by j.konrad » Thu, 2022-02-24 14:51 |
2 |
by j.konrad Fri, 2022-02-25 14:14 |
|
|
Writing value to both VESCs on FocFox Unity by agraham » Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
|
|
Discrepancies between VESC Tool 3.01 Motor Settings & XML config file by j.konrad » Sat, 2022-01-15 22:13 |
3 |
by benjamin Mon, 2022-02-21 22:17 |
|
|
Play Store - No App - Missing by TooSlow2Care » Mon, 2022-02-14 20:18 |
3 |
by TooSlow2Care Tue, 2022-02-15 19:40 |
|
|
Vesc doesn't react to can messages from PC by BorisDeroo » Fri, 2021-12-17 16:54 |
1 |
by yuri12 Wed, 2022-02-09 17:33 |
|
|
single VESC 6+ controlled by CAN-bus by vinci » Fri, 2021-07-09 15:42 |
1 |
by yuri12 Wed, 2022-02-09 17:23 |
|
|
how to communication with arduino on vesc via CAN by yuri12 » Tue, 2022-02-08 13:16 |
0 |
by yuri12 Tue, 2022-02-08 13:16 |
|
|
Trouble downloading the tool by maxhertz » Tue, 2022-01-25 03:12 |
6 |
by frank Sat, 2022-02-05 11:02 |
|
|
Setup motor foc by Vincent LAMBERT » Thu, 2022-02-03 12:22 |
0 |
by Vincent LAMBERT Thu, 2022-02-03 12:22 |
|
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
|
current of holding by reff » Thu, 2022-01-27 16:38 |
0 |
by reff Thu, 2022-01-27 16:39 |
Log in to post new content in the forum.
