You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL » Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
|
VESC Tool Control Theory by AeonCypher » Sun, 2023-02-12 23:54 |
0 |
by AeonCypher Sun, 2023-02-12 23:54 |
|
|
Installing VESC Tool on Jetson Nano by mrburns19 » Tue, 2023-02-07 04:54 |
2 |
by mrburns19 Sun, 2023-02-12 01:44 |
|
|
Hall sensor data is all 0. What do? by Byproduct » Sat, 2023-01-14 14:39 |
0 |
by Byproduct Wed, 2023-02-08 11:21 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
duty cicle 95% but current not at max by rodrigo.baronio » Mon, 2023-02-06 15:52 |
0 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
|
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc » Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
Motors spin up during detection but then won't move by jordan314 » Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
IMU not working after power cycle by Lennart Duijn » Mon, 2023-01-09 22:08 |
0 |
by Lennart Duijn Mon, 2023-01-09 22:08 |
|
|
I made a Boost Current Mod by JL2579 » Tue, 2018-01-23 18:28 |
10 |
by phiger Wed, 2022-12-21 11:19 |
|
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
2 |
by Gloobox Wed, 2022-11-30 18:39 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
|
|
Serial Control From PC by aguzel » Fri, 2020-08-21 02:45 |
3 |
by Jens Mon, 2022-11-28 20:40 |
|
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
Motor always accelerates to maximum speed by zapshe » Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
|
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
|
Problem to configure my esc with PWM-signal by Lucar » Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
|
|
PPM Pulselength mapping by Shaftdriver » Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
|
|
Vesc efficiency through log (.CSV) by th0masrtg » Tue, 2022-11-22 10:08 |
0 |
by th0masrtg Tue, 2022-11-22 10:08 |
|
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
Log in to post new content in the forum.
