You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
4.2 hw Erpm bldc mode by Katt on Wed, 2021-01-27 15:48 |
2 |
by Katt Tue, 2021-02-02 14:16 |
General discussion | |
|
48N32P sync loss by roque.canales on Fri, 2023-08-18 11:01 |
by roque.canales Fri, 2023-08-18 11:01 |
General discussion | ||
|
48V Battery cuts off while doing Motor Wizard by NiZZioN on Sun, 2022-04-24 15:31 |
1 |
by kexbox Fri, 2022-05-06 16:32 |
Third Party Hardware | |
|
48v problems by vufmihai on Wed, 2020-07-22 22:53 |
2 |
by vufmihai Fri, 2020-07-31 07:25 |
VESC Tool | |
|
4k monitor problem by nlabs on Wed, 2017-11-01 07:36 |
3 |
by benjamin Fri, 2017-11-03 09:22 |
VESC Tool | |
|
4kw BLDC hybrid system help by thardi10 on Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
General discussion | |
|
4wd rover using hub-motors by mhyer on Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
General discussion | |
|
5.02 Firmware on Trampa VESC 6 MKVI? by maxhertz on Sun, 2023-01-15 13:58 |
2 |
by maxhertz Mon, 2023-01-16 00:24 |
General discussion | |
|
5000 rpm BLDC, 1600 rpm FOC by scubersteve on Mon, 2022-03-21 03:10 |
1 |
by skyline1970 Fri, 2022-03-25 18:45 |
VESC Tool | |
|
5phase Vesc based on 75/300 by BartE on Thu, 2020-03-05 23:17 |
8 |
by vadicus Sun, 2020-03-08 05:51 |
General discussion | |
|
5V/serial weirdness when using FOC by wihrl on Sat, 2019-06-15 12:57 |
1 |
by frank Fri, 2019-06-28 14:13 |
General discussion | |
|
6 Phase Motor - How to Drive it? by vitormhenrique on Wed, 2020-02-19 05:47 |
2 |
by Badkad Fri, 2020-03-20 19:36 |
General discussion | |
|
6.05 For IOS by NetworkDir on Tue, 2024-08-27 20:38 |
1 |
by electricfox Wed, 2024-08-28 07:14 |
VESC Tool | |
|
6MK6 Can Statusmessages by maxmertins on Fri, 2024-09-20 11:36 |
1 |
by Angelo99 Tue, 2025-01-07 10:18 |
VESC Tool | |
|
75 / 300 vesc by craig w on Thu, 2021-12-16 03:36 |
1 |
by electricfox Thu, 2021-12-16 15:29 |
General discussion | |
|
75 V 300 A only reading MOSFET temperature 1 in VESC Tool by ryanbohm on Thu, 2024-02-29 01:00 |
by ryanbohm Thu, 2024-02-29 01:00 |
VESC Original Hardware | ||
|
75/250 question/issue by Petre Daniel Stroe on Sat, 2022-12-10 14:51 |
1 |
by frank Sat, 2022-12-10 21:13 |
General discussion | |
|
75/300 connection issues FW3.6 by renaudbarbier on Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
General discussion | |
|
75/300 Large inrunner problem (video) by dk-odense on Mon, 2019-11-04 21:53 |
1 |
by frank Tue, 2019-11-05 09:06 |
General discussion | |
|
75/300 Layout or gerbers by Chapel81 on Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
VESC Original Hardware |
Pages
