You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
VESC packet fram-size by Yosh101 on Fri, 2022-09-30 15:34 |
by Yosh101 Fri, 2022-09-30 15:34 |
General discussion | ||
|
paltatech v0.2 HW not supported in latest firmware? by samuelis01 on Sun, 2019-10-27 22:52 |
by samuelis01 Sun, 2019-10-27 22:52 |
VESC Firmware | ||
|
Minimum System Requirements for VESC Tool 3.01 under Windows by j.konrad on Mon, 2022-01-24 21:48 |
by j.konrad Mon, 2022-01-24 21:48 |
VESC Tool | ||
|
Rickshaw Motor - Typical 48V 1000W motors available by sweendog311 on Wed, 2023-09-20 22:52 |
by sweendog311 Wed, 2023-09-20 22:52 |
General discussion | ||
|
Sinusoidal commutation by shaman on Wed, 2020-06-03 23:42 |
by shaman Wed, 2020-06-03 23:42 |
Feature Requests | ||
|
Using Hall as encoder input by Offline on Tue, 2021-01-19 10:41 |
by Offline Mon, 2021-02-08 10:19 |
General discussion | ||
|
NEW HARDWARE RELEASED!!! | DF_ESC Electric Motor Controller | YouTube Series Walkthrough by d.fresu on Mon, 2023-08-14 18:29 |
by d.fresu Mon, 2023-08-14 18:29 |
General discussion | ||
|
Multiple VESCs on the same battery by Riccio on Wed, 2022-04-20 22:09 |
by Riccio Wed, 2022-04-20 22:09 |
General discussion | ||
|
duty cicle 95% but current not at max by rodrigo.baronio on Mon, 2023-02-06 15:52 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
VESC Tool | ||
|
VESC Replacing Shunt Resistor with Hall Current Sensor？ by happy85 on Fri, 2025-07-18 06:21 |
by happy85 Fri, 2025-07-18 11:51 |
General discussion | ||
|
Vesc_tool running error by kwlimm on Sun, 2020-01-19 10:01 |
by kwlimm Sun, 2020-01-19 10:01 |
General discussion | ||
|
VESC_75_300 by jk007 on Fri, 2021-03-19 02:41 |
by jk007 Fri, 2021-03-19 02:41 |
VESC Original Hardware | ||
|
Older version of VESC Tool by Gas_Sn4ke on Fri, 2018-11-30 09:28 |
by Gas_Sn4ke Fri, 2018-11-30 09:28 |
VESC Tool | ||
|
vesc_tool 6 and vesc 4.12 -> motor setup of small outrunner not working by Gawarmel on Thu, 2024-02-29 14:56 |
by Gawarmel Thu, 2024-02-29 14:56 |
VESC Tool | ||
|
Throttle cutout or no response...MK6 + CA3 + Older Stand alone shunt by craigoroszi on Tue, 2025-06-03 05:24 |
by craigoroszi Tue, 2025-06-03 05:24 |
Third Party Hardware | ||
|
Power by kuba12 on Sun, 2021-03-14 20:46 |
by kuba12 Mon, 2021-03-15 15:10 |
General discussion | ||
|
PPM Position over CAN bus? by walleywalker on Thu, 2021-12-02 18:47 |
by walleywalker Thu, 2021-12-02 18:47 |
General discussion | ||
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors on Sat, 2018-04-28 10:18 |
by ev_motors Sat, 2018-04-28 10:18 |
General discussion | ||
|
Closed Loop Control Not Working by Ayden1717 on Sun, 2024-07-14 19:20 |
by Ayden1717 Sun, 2024-07-14 19:20 |
General discussion | ||
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 on Fri, 2020-04-10 12:33 |
by olaf2273 Mon, 2020-04-27 15:34 |
General discussion |
Pages
