You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
VEC 4.20 50A current limitations by Jean-Michel RAVON on Thu, 2021-03-18 14:16 |
by Jean-Michel RAVON Thu, 2021-03-18 14:16 |
General discussion | ||
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 14:19 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
General discussion | ||
|
forward, reverse, regen by ronmotor on Thu, 2022-11-10 22:37 |
2 |
by velolac Tue, 2022-11-15 12:06 |
General discussion | |
|
Kill switch only stopping one motor by bmblank on Thu, 2024-01-04 22:30 |
1 |
by electricfox Sat, 2024-01-06 13:39 |
General discussion | |
|
Motor rotation direction by e-biker on Fri, 2017-12-22 15:02 |
2 |
by e-biker Tue, 2018-01-02 13:15 |
General discussion | |
|
Roll-to-start VESC by dsuresh on Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
General discussion | |
|
How to use an IMU and a PPM remote parallel by Gos1 on Tue, 2022-10-25 15:28 |
by Gos1 Wed, 2022-10-26 10:57 |
General discussion | ||
|
Flipsky Mini FSESC 6.7 Pro Red LED flashes every two seconds by never on Sun, 2023-12-17 08:59 |
by never Sun, 2023-12-17 08:59 |
General discussion | ||
|
75200 3.3 or 5v short circuit after 10 mins of use by Vassily on Thu, 2025-02-27 23:26 |
by Vassily Thu, 2025-02-27 23:26 |
General discussion | ||
|
Best way to stop "de-sync" of motors by Paul15578 on Tue, 2017-12-05 04:57 |
11 |
by Dillon Mon, 2018-11-19 02:11 |
General discussion | |
|
Wand Displaying Wrong Voltage %. by WastedYouth on Sat, 2021-10-23 17:37 |
by WastedYouth Sat, 2021-10-23 17:37 |
General discussion | ||
|
VESC as generator - settings confirmation by justinlsquire on Mon, 2022-06-06 02:44 |
by justinlsquire Mon, 2022-06-06 02:44 |
General discussion | ||
|
Erpm effect on power. by TONY61 on Mon, 2025-02-10 10:28 |
1 |
by Groundspeed100 Tue, 2025-03-11 16:13 |
General discussion | |
|
USB can not recognize by xiaofeixiak on Sat, 2018-11-24 03:20 |
1 |
by sam.vanratt Sat, 2018-11-24 14:44 |
General discussion | |
|
What is limiting the speed? by ProgramThyself on Wed, 2021-10-06 20:07 |
7 |
by ProgramThyself Sun, 2021-10-17 19:08 |
General discussion | |
|
Potentiometer in adc2 by Sandro luis on Sat, 2024-05-11 17:52 |
2 |
by Sandro luis Sun, 2024-05-12 02:56 |
General discussion | |
|
Hall sensor port repeatedly fried on original hardware by Rc 44 on Fri, 2025-10-24 22:44 |
by Rc 44 Fri, 2025-10-24 22:44 |
General discussion | ||
|
How to make VESC 4.12 can work with 14S batteries? by Ken_chen on Sat, 2018-04-21 04:39 |
5 |
by Roger Wolff Sun, 2018-05-20 08:36 |
General discussion | |
|
Master Slave Controller for Motor by Blemot on Tue, 2019-03-19 09:46 |
by Blemot Tue, 2019-03-19 09:46 |
General discussion | ||
|
Is this (low-inertia) application likely to be problematic by aabill on Sat, 2019-11-23 20:54 |
2 |
by aabill Thu, 2019-11-28 14:36 |
General discussion |
Pages
