You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:42 |
by alexshen2012 Fri, 2022-07-01 05:42 |
General discussion | ||
|
what do you guys think about this "curr_samp_volt "? by jem on Thu, 2019-08-08 14:45 |
by jem Thu, 2019-08-08 14:45 |
VESC Firmware | ||
|
help needed with raptor 2 remote by dave9401 on Mon, 2020-11-02 10:26 |
by dave9401 Mon, 2020-11-02 10:26 |
General discussion | ||
|
Maximum Motor RPM will not reached by Skyver on Sun, 2022-01-23 10:53 |
by Skyver Sun, 2022-01-23 10:53 |
General discussion | ||
|
VESC 6, astroflight 3215, loosing sync with freewheel by Rouckie on Mon, 2020-05-11 00:22 |
by Rouckie Mon, 2020-05-11 00:22 |
VESC Original Hardware | ||
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis on Sat, 2019-04-27 10:09 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
VESC Tool | ||
|
Flipsky losing its settings by jrowe on Tue, 2019-04-16 00:34 |
by jrowe Tue, 2019-04-16 00:34 |
Third Party Hardware | ||
|
Dutycycle set using uart problem by Raja Sharma on Tue, 2020-07-21 21:38 |
by Raja Sharma Tue, 2020-07-21 21:38 |
VESC Firmware | ||
|
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion | ||
|
ignore this by tobe81cwb on Tue, 2022-06-21 18:51 |
by tobe81cwb Tue, 2022-07-19 16:44 |
General discussion | ||
|
Bench Testing by usaevo7 on Tue, 2023-04-25 16:50 |
by usaevo7 Tue, 2023-04-25 16:50 |
General discussion | ||
|
Programming VESC through CANbus adapter by Filcas on Sat, 2020-03-28 11:43 |
by Filcas Sat, 2020-03-28 11:43 |
VESC Tool | ||
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 on Wed, 2022-06-08 17:33 |
by x78163 Wed, 2022-06-08 17:33 |
General discussion | ||
|
How to adjust ADC1 parameters to adjust the speed (not working) by player107 on Fri, 2023-04-14 13:46 |
by player107 Fri, 2023-04-14 13:46 |
VESC Tool | ||
|
Current measurement VESC Tool 1.16 by mdbb on Thu, 2020-03-19 17:16 |
by mdbb Thu, 2020-03-19 17:16 |
VESC Tool | ||
|
Center-aligned PWM and ADC sampling. Custom firmware by ecodev on Wed, 2020-10-07 10:42 |
by ecodev Wed, 2020-10-07 10:42 |
VESC Firmware | ||
|
Power Switch by flyingbrike on Wed, 2021-09-08 13:47 |
by flyingbrike Wed, 2021-09-08 13:47 |
General discussion | ||
|
Motor detection failed/ 0 faults by jnweb29 on Sat, 2017-12-23 21:07 |
by jnweb29 Sat, 2017-12-23 21:07 |
VESC Tool | ||
|
24v Kobalt Powered Sunjoe Mower by mistersketchman on Sun, 2020-08-02 01:54 |
by mistersketchman Sun, 2020-08-02 01:55 |
Third Party Hardware |
Pages
