You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
Firmware Updating to run X2 Pro remote for VESC6.6 by Caddy on Sat, 2020-06-27 19:30 |
by Caddy Sat, 2020-06-27 19:30 |
VESC Firmware | ||
Squealing noise and failed foc detection by sdobbie on Sat, 2021-10-23 17:00 |
by sdobbie Sun, 2021-10-24 20:05 |
VESC Development and Beta Testing | ||
PID Speed Control code....for NRF by Dimitri on Tue, 2017-10-03 07:16 |
by Dimitri Tue, 2017-10-03 07:18 |
VESC Firmware | ||
Serial Communication in Non-RT System by Jack_Li on Fri, 2019-07-05 15:58 |
by Jack_Li Fri, 2019-07-05 15:58 |
VESC Firmware | ||
Reconstruct detection control algorithm inside the tool by kaanozgen on Wed, 2020-02-26 18:50 |
by kaanozgen Wed, 2020-02-26 18:50 |
VESC Tool | ||
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE on Wed, 2020-09-09 03:15 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
VESC Tool | ||
Is there a way to deactivate roll to start function FW 5.02 by Philo on Sun, 2021-04-11 13:55 |
by Philo Sun, 2021-04-11 13:58 |
Third Party Hardware | ||
id/iq Table input by red.blaylock on Fri, 2020-05-22 09:20 |
by red.blaylock Fri, 2020-05-22 12:11 |
Feature Requests | ||
Apply current to brake at low speed by argon338 on Wed, 2022-08-17 08:36 |
by argon338 Thu, 2022-08-25 17:08 |
Feature Requests | ||
Apply current limits,1804 line mcpwm_foc.c by aishangmu on Wed, 2019-01-09 09:47 |
by aishangmu Wed, 2019-01-09 09:47 |
VESC Firmware | ||
9 by RoopeKuisma on Sun, 2020-05-10 21:58 |
by RoopeKuisma Sun, 2020-05-10 21:58 |
General discussion | ||
one motor spinning faster than the other? by jon218white on Mon, 2020-12-14 22:57 |
by jon218white Mon, 2020-12-14 22:57 |
VESC Tool | ||
Defining when Watt-hour / Amp-hour Data are rezeroed by isabar on Sun, 2018-06-24 10:19 |
by isabar Sun, 2018-06-24 10:19 |
Feature Requests | ||
External Bluetooth and IMU on CAN-connected VESCs by frankus on Sat, 2022-03-26 19:58 |
by frankus Sat, 2022-03-26 19:58 |
General discussion | ||
Need IRF7759 by marcel7162 on Fri, 2022-03-18 22:29 |
by marcel7162 Fri, 2022-03-18 22:29 |
Third Party Hardware | ||
Making master and slave motors communicate both ways by Sis7 on Tue, 2020-07-21 05:58 |
by Sis7 Tue, 2020-07-21 05:58 |
General discussion | ||
How to update a VESC 4.10 with a 3.36 firmware? by shingo.it on Tue, 2020-06-09 23:40 |
by shingo.it Tue, 2020-06-09 23:40 |
VESC Firmware | ||
motor stuttering and having a hard time with receiver ... help by okyuubix on Tue, 2021-09-14 23:43 |
by okyuubix Tue, 2021-09-14 23:49 |
General discussion | ||
Dual Vesc reading second wheel RPM by rdavenport3 on Tue, 2022-05-03 15:32 |
by rdavenport3 Tue, 2022-05-03 15:32 |
VESC Firmware | ||
Move FAULT pin to GPIOD_PIN2 by CTSchorsch on Tue, 2018-09-04 10:13 |
by CTSchorsch Tue, 2018-09-04 10:13 |
VESC Firmware |
Pages
