You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Where to find CAN protocol documentation? by doctarr on Tue, 2020-12-29 15:33 |
by doctarr Tue, 2020-12-29 15:33 |
General discussion | ||
|
PID Speed Controller by wysteria on Sat, 2020-12-12 10:14 |
by wysteria Sat, 2020-12-12 10:14 |
General discussion | ||
|
Generic dual drive Ebay controller speed by stefann on Wed, 2022-03-23 21:14 |
by stefann Wed, 2022-03-23 21:14 |
Third Party Hardware | ||
|
Inappropriate ioctl by Roger Wolff on Sat, 2018-06-02 17:38 |
by Roger Wolff Sat, 2018-06-02 18:04 |
VESC Tool | ||
|
bldc_interface_set_current and bldc_interface_set_rpm troubles by kristof_lr on Wed, 2019-04-24 17:20 |
by kristof_lr Wed, 2019-04-24 17:20 |
General discussion | ||
|
Noise related issues? by RDN2003 on Sun, 2020-07-26 20:17 |
by RDN2003 Sun, 2020-07-26 20:17 |
General discussion | ||
|
Problems Compiling Firmware by LB94 on Tue, 2022-11-29 00:08 |
by LB94 Tue, 2022-11-29 00:08 |
VESC Firmware | ||
|
Trying to read and set MCCONF by Jamie42 on Tue, 2020-03-24 19:47 |
by Jamie42 Tue, 2020-03-24 19:47 |
General discussion | ||
|
VESC as generator - settings confirmation by justinlsquire on Mon, 2022-06-06 02:44 |
by justinlsquire Mon, 2022-06-06 02:44 |
General discussion | ||
|
Problems with UART communication via Arduino UNO by Michael Hamm on Fri, 2022-02-04 13:29 |
by Michael Hamm Fri, 2022-02-04 13:29 |
General discussion | ||
|
Combat Robot Mods by BrianNave on Sun, 2019-02-24 17:03 |
by BrianNave Sun, 2019-02-24 17:03 |
Feature Requests | ||
|
Why i cant insert a topic? by SafrdA on Thu, 2021-04-29 20:41 |
by SafrdA Thu, 2021-04-29 20:41 |
General discussion | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Firmware | ||
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
HFI optimisation with increase in switching frequency by rainebk@bigpond... on Tue, 2022-09-13 06:53 |
by rainebk@bigpond... Tue, 2022-09-13 06:53 |
General discussion | ||
|
mcpwm_foc and mcpwm tutorial by nami1216 on Tue, 2019-10-15 07:12 |
by nami1216 Tue, 2019-10-15 07:12 |
VESC Firmware | ||
|
Do I need a motor with Hall sensor to use Vesc tool? by greew on Sun, 2020-05-31 06:48 |
by greew Sun, 2020-05-31 06:48 |
General discussion | ||
|
Why not using interrupt for Hall signal detection? by kuan on Sun, 2021-01-03 09:51 |
by kuan Sun, 2021-01-03 09:51 |
General discussion | ||
|
Choosing Motor Encoder for VESC by VRdublove on Fri, 2020-01-24 18:51 |
by VRdublove Fri, 2020-01-24 21:44 |
VESC Original Hardware |
Pages
