You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Voltage spikes on BEMF scope by Sgw32 on Wed, 2020-11-18 16:03 |
by Sgw32 Wed, 2020-11-18 16:06 |
General discussion | ||
|
Duty Cycle with BRAKE then Reverse - missing option by sp3swj on Tue, 2022-03-15 01:00 |
by sp3swj Tue, 2022-03-15 01:00 |
Feature Requests | ||
|
Got the judders by Phill Dixon on Sun, 2018-05-13 17:45 |
by Phill Dixon Sun, 2018-05-13 17:45 |
General discussion | ||
|
How to read the CAN message with CAN anlayzer by yuri12 on Thu, 2022-03-03 18:21 |
by yuri12 Thu, 2022-03-03 18:21 |
VESC Tool | ||
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 on Mon, 2020-07-06 03:09 |
by bmwman91 Mon, 2020-07-06 03:21 |
VESC Tool | ||
|
Using vesc between many motors by EliProtiva on Tue, 2021-02-16 05:32 |
by EliProtiva Tue, 2021-02-16 05:32 |
General discussion | ||
|
Configuration of underwater thruster by UnderwaterMotors on Fri, 2023-03-24 18:10 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
General discussion | ||
|
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
|
Stream UART Telemetry without a Request by AlexBenn on Thu, 2022-01-20 02:47 |
by AlexBenn Thu, 2022-01-20 02:47 |
VESC Firmware | ||
|
VESC 75/300 singnal connectors by Mikko Valtonen on Tue, 2020-05-19 21:43 |
by Mikko Valtonen Tue, 2020-05-19 21:43 |
VESC Original Hardware | ||
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion | ||
|
Remap Rotary Encoder Input to CAN (or other) by Artemis Skade on Wed, 2020-04-01 20:23 |
by Artemis Skade Wed, 2020-04-01 20:23 |
Feature Requests | ||
|
Duty vs RPM for smooth start and slow running by Davideo on Tue, 2018-04-24 14:42 |
by Davideo Tue, 2018-04-24 14:42 |
General discussion | ||
|
BLDC zero cross happens too early by Sgw32 on Thu, 2021-05-20 19:10 |
by Sgw32 Thu, 2021-05-20 19:10 |
General discussion | ||
|
Dual Motor Setup not working via CAN Bus (solved) by acleon on Fri, 2020-06-19 00:03 |
by acleon Fri, 2020-06-19 16:33 |
VESC Tool | ||
|
Regarding code documentation by hiddenzed on Mon, 2021-02-08 12:40 |
by hiddenzed Mon, 2021-02-08 12:40 |
VESC Firmware | ||
|
Prevent Wheel-slip by low-pass filtering duty cycle output by AlexBenn on Thu, 2018-09-13 07:50 |
by AlexBenn Thu, 2018-09-13 07:50 |
VESC Firmware | ||
|
Simultaneous control of two BLDC motors with VESCs via CAN bus without RC controller by sampatsr on Mon, 2023-02-27 20:21 |
by sampatsr Mon, 2023-02-27 20:21 |
General discussion | ||
|
VESC Tool Control Theory by AeonCypher on Sun, 2023-02-12 23:54 |
by AeonCypher Sun, 2023-02-12 23:54 |
VESC Tool | ||
|
Newer DRV8353RS instead of DRV8301? by whydoilive on Fri, 2021-04-02 10:24 |
by whydoilive Fri, 2021-04-02 10:24 |
General discussion |
Pages
