You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Sensored BLDC problem - RPM spikes by arsenix on Thu, 2018-12-27 05:41 |
1 |
by arsenix Thu, 2019-01-03 03:29 |
VESC Firmware | |
Hard faults in mcpwm_foc.c? by vesc_fault on Thu, 2019-01-03 07:00 |
by vesc_fault Thu, 2019-01-03 07:20 |
VESC Firmware | ||
Another Motor Detection Thread by MaksK on Wed, 2019-01-02 21:05 |
1 |
by TechAUmNu Thu, 2019-01-03 17:23 |
VESC Tool | |
highspeed motors max erpm? by themotorman on Sun, 2018-12-30 00:50 |
2 |
by TechAUmNu Thu, 2019-01-03 17:25 |
VESC Firmware | |
VESC 4.12 with big-BLDC problem by sam.vanratt on Mon, 2018-12-10 15:59 |
6 |
by sam.vanratt Thu, 2019-01-03 17:44 |
General discussion | |
ADC1 problems with Firmware/Hardware issue? by sam.vanratt on Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
General discussion | |
Fast Startup problem by sam.vanratt on Thu, 2019-01-03 17:56 |
7 |
by sam.vanratt Sun, 2019-01-06 23:25 |
General discussion | |
Apply current limits,1804 line mcpwm_foc.c by aishangmu on Wed, 2019-01-09 09:47 |
by aishangmu Wed, 2019-01-09 09:47 |
VESC Firmware | ||
VESC acceleration control on setRPM by fourchette on Tue, 2019-01-08 12:02 |
3 |
by fourchette Wed, 2019-01-09 10:38 |
General discussion | |
maytech mto91hbm-nh motors hal sensor by nolander on Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
Third Party Hardware | |
Dead VESC. Power up when motor is spinning. by Bor Zabric on Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
General discussion | |
Can not adjust the RPM on my 1350 w motor by Arne Norway on Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
General discussion | |
Firmware Modification Basics? Changing app_adc.c by striderkent on Tue, 2019-01-15 22:00 |
1 |
by striderkent Tue, 2019-01-15 22:05 |
VESC Firmware | |
4kw BLDC hybrid system help by thardi10 on Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
General discussion | |
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant on Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
VESC Firmware | |
Upload bootloader to new MCU by Jessica on Fri, 2019-01-11 14:43 |
7 |
by Jessica Wed, 2019-01-16 09:07 |
General discussion | |
Vesc 6 motor setup fault by Davo69URX on Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
General discussion | |
Change RPM of motor by Gas_Sn4ke on Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
General discussion | |
UART working great at low current, terrible at high current by Dillon on Sat, 2018-03-17 04:17 |
23 |
by Dillon Sat, 2019-01-19 04:06 |
VESC6 Beta | |
Angle offset detection by Gas_Sn4ke on Mon, 2019-01-21 07:09 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
General discussion |