You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
IMU and balancing powertrain by sunsam8 on Thu, 2020-09-03 05:03 |
by sunsam8 Thu, 2020-09-03 05:03 |
Feature Requests | ||
|
Read analog Data from ADC1 by mmobayed on Mon, 2024-03-25 21:41 |
by mmobayed Mon, 2024-03-25 21:41 |
General discussion | ||
|
VESC 60 75 IMU by Alistair Goodman on Thu, 2025-08-14 18:23 |
by Alistair Goodman Thu, 2025-08-14 18:23 |
General discussion | ||
|
Braking current after high-speed coast by ProgramThyself on Sun, 2020-08-23 06:02 |
by ProgramThyself Sun, 2020-08-23 06:02 |
VESC6 Beta | ||
|
Arduino- UART Library Question... by arranto12 on Sun, 2022-01-02 09:57 |
by arranto12 Sun, 2022-01-02 09:57 |
General discussion | ||
|
high side active low and low side active high driver signal setting in firmware. by Spencer.chen on Wed, 2021-12-15 14:00 |
by Spencer.chen Wed, 2021-12-15 14:04 |
VESC Firmware | ||
|
TMP100 I2C Sensor by CTSchorsch on Tue, 2020-04-21 15:55 |
by CTSchorsch Tue, 2020-04-21 15:55 |
VESC Firmware | ||
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt on Tue, 2022-03-15 09:06 |
by v1n23nt Tue, 2022-03-15 09:10 |
General discussion | ||
|
VESC Tool Reporting RPM Different from Scope by bayetan on Wed, 2022-11-02 15:39 |
by bayetan Wed, 2022-11-02 15:39 |
VESC Firmware | ||
|
Vesc tool mobile for raspbian by Idoff on Sat, 2019-03-30 19:24 |
by Idoff Sat, 2019-03-30 19:24 |
VESC Tool | ||
|
Issues with VESC 75/300 and VESC-Tool V3.01 by hpb66 on Fri, 2022-06-03 09:15 |
by hpb66 Fri, 2022-06-03 09:15 |
VESC Tool | ||
|
step by step ebike thorttle setup by sindre on Wed, 2019-07-03 17:59 |
by sindre Wed, 2019-07-03 17:59 |
General discussion | ||
|
Import/Export XML configs on android by badname on Mon, 2020-09-28 17:52 |
by badname Mon, 2020-09-28 17:52 |
Feature Requests | ||
|
Problems driving motors in RPM mode by jediengineer on Fri, 2023-03-10 14:03 |
by jediengineer Fri, 2023-03-10 19:51 |
General discussion | ||
|
VESC cutout using smart reverse by Brokepilot on Thu, 2024-04-25 16:50 |
by Brokepilot Thu, 2024-04-25 16:50 |
General discussion | ||
|
Is there a way to deactivate roll to start function FW 5.02 by Philo on Fri, 2021-04-16 22:28 |
by Philo Sun, 2021-04-18 11:57 |
VESC Firmware | ||
|
PAS app: limit current depending on actual velocity by dpeinado on Fri, 2022-01-21 13:49 |
by dpeinado Fri, 2022-01-21 13:49 |
VESC Firmware | ||
|
Unstable current readings over VESC CAN (UART/USB are fine) by vukstijepovic on Mon, 2025-09-15 16:59 |
by vukstijepovic Mon, 2025-09-15 16:59 |
General discussion | ||
|
Higher voltage DRV error by jarrow on Tue, 2018-03-06 10:06 |
by jarrow Tue, 2018-03-06 10:06 |
VESC Original Hardware | ||
|
VESC 6 EDU: Motor Wizard - Detection failed by Navigator_PJE on Mon, 2022-08-29 16:12 |
by Navigator_PJE Mon, 2022-08-29 16:12 |
General discussion |
Pages
