You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
Where can I ask technical questions about products? by MrSurly on Tue, 2022-04-19 05:22 |
by MrSurly Tue, 2022-04-19 05:22 |
General discussion | ||
|
Choosing Motor Encoder for VESC by VRdublove on Fri, 2020-01-24 18:51 |
by VRdublove Fri, 2020-01-24 21:44 |
VESC Original Hardware | ||
|
current control mode with duty cycle limit based on throttle by devin on Thu, 2020-01-16 05:45 |
by devin Thu, 2020-01-16 05:49 |
General discussion | ||
|
motor output voltage vs input voltage by rsarver on Wed, 2021-03-17 15:55 |
by rsarver Wed, 2021-03-17 15:55 |
General discussion | ||
|
Lawn mower by charper on Mon, 2018-12-03 14:25 |
by charper Mon, 2018-12-03 14:25 |
General discussion | ||
|
[solved] Firmware 5.01 gcc compile fail.. need some insight by Bill Somerville on Tue, 2020-11-03 19:44 |
by Bill Somerville Fri, 2020-11-06 23:20 |
VESC Firmware | ||
|
Terminal Command for Current? by Mannerow on Thu, 2020-10-29 23:07 |
by Mannerow Thu, 2020-10-29 23:07 |
VESC Tool | ||
|
Direct drive wheel ac servo+vesc by adilrepas on Wed, 2021-05-26 12:50 |
by adilrepas Wed, 2021-05-26 12:58 |
General discussion | ||
|
Request Feature to add minimum Battery Voltage value in addition to duty cycle for field weakening by aquaponiccowboy on Mon, 2022-10-17 04:49 |
by aquaponiccowboy Mon, 2022-10-17 04:50 |
Feature Requests | ||
|
how to communication with arduino on vesc via CAN by yuri12 on Tue, 2022-02-08 13:16 |
by yuri12 Tue, 2022-02-08 13:16 |
VESC Tool | ||
|
VESC Tool for Android & GPS/GNSS sharing? by ahagge on Fri, 2021-10-01 05:04 |
by ahagge Fri, 2021-10-01 05:04 |
VESC Tool | ||
|
Encoder support in BLDC by dirkvl on Sat, 2021-09-18 12:21 |
by dirkvl Sat, 2021-09-18 12:21 |
Feature Requests | ||
|
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
by dgarciasoto Wed, 2022-04-27 07:11 |
VESC Firmware | ||
|
FOC settings are working in one VESC hardware and not in another VESC hardware with same hardware version ( VESC 6MKVI ) by Pranit Bhamare on Fri, 2023-02-17 07:17 |
by Pranit Bhamare Fri, 2023-02-17 07:17 |
General discussion | ||
|
Auxiliary Output Mode pin# by garyp on Sat, 2020-08-22 18:17 |
by garyp Sat, 2020-08-22 18:17 |
General discussion | ||
|
Cruise function already implemented? by sam.vanratt on Wed, 2019-01-02 17:05 |
by sam.vanratt Wed, 2019-01-02 17:20 |
General discussion | ||
|
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ on Mon, 2019-09-16 19:36 |
by MaddiQ Mon, 2019-09-16 19:36 |
VESC Firmware | ||
|
(CLOSED)Custom FW based on beta "could not deserialize" by pe on Wed, 2021-12-15 11:48 |
by pe Wed, 2021-12-15 15:18 |
VESC Development and Beta Testing | ||
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 on Mon, 2022-08-01 18:08 |
by moose09876 Mon, 2022-08-01 18:08 |
General discussion |
Pages
