You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
LoRa Support by CTSchorsch on Fri, 2021-12-17 13:59 |
by CTSchorsch Fri, 2021-12-17 13:59 |
Third Party Hardware | ||
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq on Wed, 2022-08-03 17:03 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
VESC Tool | ||
|
(Watchdog) - Resets with multipole engine. by edilger on Mon, 2023-06-26 12:33 |
by edilger Mon, 2023-06-26 12:33 |
VESC Firmware | ||
|
Dronecan 1036.StatusExtended message for motor temp by cjmssmd on Wed, 2024-09-04 02:05 |
by cjmssmd Wed, 2024-09-04 02:05 |
Feature Requests | ||
|
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani on Thu, 2019-09-12 19:00 |
by arifbustani Thu, 2019-09-12 19:00 |
General discussion | ||
|
Motors wont turn independently by huffauden19 on Mon, 2020-11-30 06:24 |
by huffauden19 Mon, 2020-11-30 06:24 |
VESC Tool | ||
|
VESC appears to loose sync when increasing throttle by srinath on Sun, 2023-06-04 04:11 |
by srinath Sun, 2023-06-04 04:11 |
General discussion | ||
|
vesc hardware 4.12 by BasilBrushy on Fri, 2020-04-24 11:56 |
by BasilBrushy Fri, 2020-04-24 11:56 |
Third Party Hardware | ||
|
Startup codes? by anthonys on Sat, 2021-06-19 17:29 |
by anthonys Sat, 2021-06-19 17:29 |
VESC Tool | ||
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 14:19 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
General discussion | ||
|
How to use an IMU and a PPM remote parallel by Gos1 on Tue, 2022-10-25 15:28 |
by Gos1 Wed, 2022-10-26 10:57 |
General discussion | ||
|
Flipsky Mini FSESC 6.7 Pro Red LED flashes every two seconds by never on Sun, 2023-12-17 08:59 |
by never Sun, 2023-12-17 08:59 |
General discussion | ||
|
75200 3.3 or 5v short circuit after 10 mins of use by Vassily on Thu, 2025-02-27 23:26 |
by Vassily Thu, 2025-02-27 23:26 |
General discussion | ||
|
Control current PID from UART by Koxx on Wed, 2021-02-17 20:27 |
by Koxx Wed, 2021-02-17 20:27 |
VESC Firmware | ||
|
Wand Displaying Wrong Voltage %. by WastedYouth on Sat, 2021-10-23 17:37 |
by WastedYouth Sat, 2021-10-23 17:37 |
General discussion | ||
|
VESC as generator - settings confirmation by justinlsquire on Mon, 2022-06-06 02:44 |
by justinlsquire Mon, 2022-06-06 02:44 |
General discussion | ||
|
vesc free role? by iplayfast on Mon, 2021-02-08 22:13 |
by iplayfast Mon, 2021-02-08 22:13 |
General discussion | ||
|
Double current single direction common ground DC motor driving by fdryk on Tue, 2023-03-28 18:36 |
by fdryk Wed, 2023-03-29 10:44 |
Feature Requests | ||
|
Vesc mAh reading by th0masrtg on Tue, 2020-09-29 08:48 |
by th0masrtg Wed, 2020-09-30 19:58 |
VESC Tool | ||
|
Hall sensor port repeatedly fried on original hardware by Rc 44 on Fri, 2025-10-24 22:44 |
by Rc 44 Fri, 2025-10-24 22:44 |
General discussion |
Pages
