You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Multiple VESC's in duty cycle mode by Rudolf10000 on Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
VESC Tool | |
|
ADC MAX Voltage 5volt ? by liteglow on Sat, 2020-07-25 23:48 |
by liteglow Sat, 2020-07-25 23:48 |
VESC Tool | ||
|
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
|
Bug found in VESC tool 6.05 related to VESC BMS by f.damien12 on Wed, 2025-04-09 17:11 |
by f.damien12 Wed, 2025-04-09 17:13 |
VESC Tool | ||
|
Vesc tool 1.26.. issue with firmware updates? by beetbocks on Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
VESC Tool | |
|
FOC with 2 Poles and only 6 Windings? by martin2day on Fri, 2020-07-17 08:16 |
2 |
by martin2day Sat, 2020-07-18 10:36 |
VESC Tool | |
|
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
VESC Tool | |
|
Command Line Options by Dude on Wed, 2017-10-18 22:56 |
6 |
by woodmastr Thu, 2022-07-21 14:23 |
VESC Tool | |
|
VESC Tool disappeared from App Store by volkswagenbug on Thu, 2024-06-13 21:40 |
4 |
by Sybernetix Sat, 2024-06-15 11:32 |
VESC Tool | |
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne on Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
VESC Tool | |
|
How VESCTOOL Determines the foc_sensor_mode by NATUITION on Tue, 2024-05-28 11:29 |
by NATUITION Tue, 2024-05-28 11:29 |
VESC Tool | ||
|
PPM throttle detected in Vesc Tool but has no effect on motor by maxim1977 on Sat, 2025-07-26 06:03 |
1 |
by ftpkmarcelo Sun, 2025-08-10 06:07 |
VESC Tool | |
|
I made a Boost Current Mod by JL2579 on Tue, 2018-01-23 18:28 |
10 |
by phiger Wed, 2022-12-21 11:19 |
VESC Tool | |
|
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas on Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
VESC Tool | |
|
Dual VESC and One Motor Stops Spinning by f0n on Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
VESC Tool |
Pages
