You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
3 speed switch by de-bodgery on Sat, 2021-08-21 02:22 |
17 |
by Oscar Lozano Gimenez Mon, 2023-05-22 14:07 |
General discussion | |
|
Current Sensing in VESC by Toshi Sharma on Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
General discussion | |
|
Two vescs, one motor? by RoopeKuisma on Sun, 2020-05-10 22:11 |
17 |
by Elwin Thu, 2021-10-28 09:48 |
General discussion | |
|
VESC Tool for old hardware by benjamin on Fri, 2017-07-07 11:49 |
17 |
by frank Mon, 2017-10-09 15:56 |
VESC6 Beta | |
|
Driving the FETs.... by Roger Wolff on Sat, 2017-10-21 16:37 |
17 |
by Roger Wolff Mon, 2017-12-11 20:55 |
Third Party Hardware | |
|
simulate turboprop engine ... using VESC, how to.... by Eckehard on Wed, 2020-06-10 22:32 |
17 |
by Eckehard Thu, 2020-07-02 22:34 |
General discussion | |
|
Hall sensor filter on VESC flier board by raess on Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
General discussion | |
|
VESC-Project Open Source status ? by Pimousse on Tue, 2018-01-23 11:41 |
18 |
by velolac Thu, 2023-02-09 11:33 |
The VESC-Project | |
|
Current out of Sync by CTSchorsch on Sat, 2020-08-01 13:24 |
18 |
by CTSchorsch Fri, 2020-09-04 11:28 |
Third Party Hardware | |
|
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
|
VESC Tool Error - updating fw on old hw 4.7 VESCs by sl33py on Sun, 2017-07-09 05:43 |
18 |
by Maxid Mon, 2025-05-12 10:28 |
VESC6 Beta | |
|
VESC with really high KV by bengce on Sun, 2020-06-21 11:18 |
18 |
by bengce Thu, 2020-08-13 14:11 |
General discussion | |
|
Motor Values in VESC-Tool 2019 by frank on Wed, 2019-02-27 09:40 |
19 |
by Onarb Kabr Wed, 2025-01-15 13:28 |
VESC Tool | |
|
UART communication by EthB on Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
General discussion | |
|
High Voltage ESC (HiVEsc) 150V 500A by e-biker on Thu, 2019-08-15 14:45 |
19 |
by jarrancho Fri, 2020-12-04 11:35 |
Third Party Hardware | |
|
Is electronic brake always REGEN? by Tilman Baumann on Tue, 2018-04-10 11:16 |
19 |
by henxan Sun, 2019-11-17 18:30 |
General discussion | |
|
position control with gearbox by raess on Tue, 2018-09-25 23:48 |
19 |
by Artabotak Tue, 2024-12-03 08:48 |
General discussion | |
|
Using a VESC V4.12 for a machining lathe by Krampas on Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
|
Efficiency Control by devin on Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
General discussion | |
|
VESC CNC case - Feedbacks by Pimousse on Wed, 2017-06-07 17:58 |
19 |
by Necromenz Mon, 2017-06-12 23:44 |
VESC6 Beta |
Pages
