You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Question about FOC Wizard by proget.snc on Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
VESC Tool | |
|
I have the BLUEZ... Or rather... I don't. by Roger Wolff on Wed, 2018-01-03 16:03 |
6 |
by arvidb Wed, 2018-01-17 14:26 |
VESC Tool | |
|
Sailboat regen by flydr2 on Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
VESC Tool | |
|
beginners by viniii00 on Tue, 2021-11-23 20:12 |
2 |
by FOURDAN Mon, 2022-07-04 10:13 |
VESC Tool | |
|
UI problem by Zeos on Fri, 2026-01-30 11:29 |
by Zeos Fri, 2026-01-30 11:29 |
VESC Tool | ||
|
Need help: encoder shows 9.6 rotations per 1 motor rotation (9.6:1 gearbox) by Alico on Thu, 2025-12-11 14:41 |
by Alico Thu, 2025-12-11 14:41 |
VESC Tool | ||
|
PPM problems by rufr123 on Sat, 2020-10-31 20:49 |
1 |
by thefallen Tue, 2020-11-03 00:29 |
VESC Tool | |
|
VESC Tool on Windows 10 32 Bit doesn't open by Red_Speedster on Mon, 2021-05-31 16:33 |
2 |
by frank Wed, 2022-01-26 08:21 |
VESC Tool | |
|
Smart Reverse Minimum Erpm by ZenRides on Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
VESC Tool | |
|
Dual Motor Setup not working via CAN Bus (solved) by acleon on Fri, 2020-06-19 00:03 |
by acleon Fri, 2020-06-19 16:33 |
VESC Tool | ||
|
If firmware aint broke, dont fix it. by nickw1881 on Thu, 2019-10-31 07:32 |
3 |
by frank Wed, 2019-11-06 12:39 |
VESC Tool | |
|
Incorrect speed too high by Michele84 on Wed, 2021-07-21 15:48 |
by Michele84 Wed, 2021-07-21 15:48 |
VESC Tool | ||
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen on Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
VESC Tool | |
|
Vesc Tool not opening on windows computer by maccert on Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
VESC Tool | |
|
How to Enable kill switch support in Firmware 5.03 by iserai2r on Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
VESC Tool | |
|
foc openloop not starting motor on higher erpm by Alan oldguy on Thu, 2018-09-06 08:43 |
8 |
by technicc Mon, 2022-03-28 09:23 |
VESC Tool | |
|
Use ADC2 as reverse button for ADC+UART/Current Reverse Button by jessejay356 on Mon, 2024-09-23 01:06 |
by jessejay356 Mon, 2024-09-23 01:06 |
VESC Tool | ||
|
Motor temperature, how to set limit >120 C ? by RSR on Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
VESC Tool | |
|
Реверс вращения двигателя by Wolod5 on Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
VESC Tool | |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp on Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
VESC Tool |
Pages
